Titan Tool LX-65 Manual

Open as PDF

next previous

English

Maintenance

Follow all safety precautions as described in the Safety

Precautions section of this manual before proceeding.

NOTE: Refer to the Parts List section in this manual for part

identication.

Replacing/Servicing the Seal Assembly

Ifyourspraygunleaksorspitsatthetipwhenyoureleasethetrigger,

theneedleorseatisworn,damaged,ordirtyandmustbereplacedor

cleaned.

Never attempt to perform maintenance on the spray gun

without first performing the “Pressure Relief Procedure.”

 1. Disconnecttheuidhosefromthegun.

 2. Removethetipandtipguard.

 3. Withthetriggerdepressed,removethediffuserfromthefrontof

thegun.

 4. Removethelocknut,rearhousing,andretractorpinsfromthe

rearofthegunhead.

 5. Removethesealassemblyfromthefrontofthegunheadby

pushingorgentlytappingatthebackofthesealassembly.

 6. Soaktheremovedpartsintheappropriatesolventandwipe

clean.

 7. Inspectthepartsforwearordamageandusenewpartsduring

reassemblyofthegun,whennecessary.

NOTE: Lubricate all packings and moving parts before

reassembly with a lithium-based grease.

 8. Installthesealassemblyintothefrontofthegunhead.

 9. Installtheretractorpinsintotherearofthegunhead.Slidethe

rearhousingontotheretractorpinsandsecureinpositionwith

thelocknut.

 10. WIththetriggerdepressed,installthediffuserintothefrontofthe

gunheadandtightensecurelywithawrench.

 11. Performthe“AdjustingtheSealAssembly”proceduredescribed

below.

Adjusting the Seal Assembly

Proper adjustment of the seal assembly is essential to

ensure positive shut-off when the trigger is released.

 1. Tightenthelocknutuntiltherearhousingisushagainstthegun

head.

 2. Unscrewthelocknut3/4ofaturn.

NOTE: To check the adjustment of the seal assembly:

1. Move the gun trigger lock to the locked position.

2. Pull the trigger.

With the trigger lock engaged, there should be 1/32” of

movement between the lock nut and the rear housing

while pulling the trigger.

Replacing/Removing the Filter

 1. Pullthebottomofthetriggerguardforwardsothatitcomesloose

fromthehandleassembly.

 2. Loosenandremovethehandleassemblyfromthegunhead.

 3. Pulltheoldlteroutofthegunhead.

 4. Slidethenewlter,taperedendrst,intothegunhead.

 5. Makesurethehandlesealisinpositionandthreadthehandle

assemblyintothegunheaduntilsecure.

 6. Snapthetriggerguardbackontothehandleassembly.

Gun Filter Chart

Part

Number

Application Filter

Type

Color of

Filter

Body

0089960 Synthetic resin,

enamels, clean

varnishes, stains

azures

Extrafine red

0089959 Base coat enamels,

primer enamels,

fillers, marking paints,

textured enamels

Fine yellow

0089958 Emulsions,

latex paints,

acrylic paints

Medium white

0089957 Filler paints,

large area surfaces

Coarse green

Parts List

Item Part # Description Quantity

1 0296228 Gunhead ..................................................1

 2 0296284 Triggerscrew,short ..................................1

 3 0296285 Triggerassembly,4-ngergun .................1

 4 0296230 Triggerguard ............................................1

 5 0296270 Sealassembly ..........................................1

 6 0296404 Diffuser .....................................................1

 7 0297045 Seal ..........................................................1

 8 661-517 Tipassembly,

   (includesitems7and10) .........................1

 9 661-012 Tipguard .................................................1

 10 0297007 Tipseal .....................................................1

 11 9910201 Locknut ....................................................1

 12 0296222 Rearhousing ............................................1

 13 0296286 Retractorpin .............................................2

 14 0296287 Triggerscrew,long ...................................1

 15 0089958 Filter,medium ...........................................1

 16 0296289 Handleseal...............................................1

 17 0296342 Handle ......................................................1

 18 0296343 Spring .......................................................1

 19 0347706 Swivel .......................................................1

 20 0296291 Triggerassembly,2-ngergun .................1

 21 0279185 Collarassembly,2-ngergun ...................1

  0296345 Handleassembly(includesitems17–19)

  0296294 Gunrepairkit(includesitems5,6,and11)

  0286747 Gunsidelabel