JVC GR-DX97 Digital Camera User Manual


 
EDITING
44 EN
MasterPage: Left
Automatic Editing To VCR
13 Rewind the tape in the camcorder to the beginning
of the scene you want to edit and press PAUSE (9).
14 Press VCR REC STBY (79) on the remote control,
or manually engage the VCRs Record-Pause mode.
15 Press the Recording Start/Stop Button on the
camcorder. Editing proceeds as programmed, right
through to the end of the last registered scene.
When dubbing is complete, the camcorder enters the
Pause mode, and the VCR enters its Record-Pause mode.
If you do not register an Edit-Out point, the tape will be
dubbed all the way to the end automatically.
If you operate the camcorder during automatic editing, the
VCR will enter its Record-Pause mode and automatic
editing will stop.
16 Engage the Stop modes for the camcorder and the
VCR.
To make the R.A.Edit counter display disappear, press
R.A.EDIT ON/OFF on the remote control.
NOTES:
Pressing R.A.EDIT ON/OFF on the remote control clears
all settings registered during Random Assemble Editing.
When the editing cable is connected to the remote controls
PAUSE IN connector during dubbing, make sure the remote
control is pointed at the VCRs sensor, and the path
between the two is unobstructed.
Random Assemble Editing may not function properly when
using a tape including several duplicated time codes.
(pg. 17)
For More Accurate Editing
Some VCRs make the transition from Record-Pause to
Record mode faster than others. Even if you begin
editing for the camcorder and the VCR at exactly the
same time, you may lose scenes you wanted, or find that
you have recorded scenes you did not want. For a cleanly
edited tape, confirm and adjust the timing of the
camcorder against your VCR.
Diagnosing VCR/Camcorder Timing
1 Play back the tape in the camcorder, then point the
remote control at the camcorders remote sensor and
press R.A.EDIT ON/OFF.
Random Assemble Editing Menu
appears.
2 Perform Random Assemble
Editing on Program 1 only. In order
to check VCR and camcorder
timing, select the beginning of a
scene transition as your Edit-In
point.
3 Play back the dubbed scene.
If any images from the scene prior to the transition you
chose for your Edit-In point were recorded, that means your
VCR moves too quickly from Record-Pause to Record
mode.
If the scene you tried to dub starts in progress, the VCR is
slow to start recording.
Adjustment Of VCR/Camcorder Timing
4 Press R.A.EDIT ON/OFF to make the Random
Assemble Editing menu disappear, then press MENU.
The Menu Screen appears.
5 Press SET to select t. The VIDEO Menu appears.
6 Press or to select SYNCHRO, and press SET.
The value for SYNCHRO is highlighted. (Factory-
preset: ±0.0)
7 Based on the diagnostics performed, you can now
advance the VCRs record timing by pressing . You
can also delay the VCRs record timing by pressing .
The adjustment range is from 1.3 to +1.3 seconds, in 0.1-
second increments.
Press SET to finish the setting.
8 Press or to select BRETURN, and press SET
twice.
Now perform Random Assemble Editing beginning with
step 6 on page 43.
NOTES:
Before performing actual Random Assemble Editing, do a
few Random Assemble Editing trial runs to check whether
the value you have input is appropriate or not, and make
adjustments accordingly.
Depending on the recorder, there may be situations where
the timing difference cannot be fully corrected.
1
2
3
4
5
6
7
8
––: –– ~
~
~
~
~
~
~
~
––
NIOUT
MOD E
:
––
0
:
000
TOTAL
CODETIME
Program 1
GR-DX97US.book Page 44 Monday, February 9, 2004 2:28 PM