Filter
Top Products
EN
18
FOR RECORDING
Snapshot
This feature lets you record still images that look like
photographs onto a tape.
SNAPSHOT MODE SELECTION
1 Set the Power Switch 8 to “ ” while pressing
down the Lock Button 0 located on the switch. Open
the LCD monitor fully or pull out the viewfinder fully.
2 Press MENU 2. The Menu Screen appears.
3 Press + or – 3 to select “ (CAMERA)”, then
press SELECT/SET 1.
4 Press + or – 3 to select “SNAP MODE”, then press
SELECT/SET 1.
5 Press + or – 3 to select the desired Snapshot
mode, then press SELECT/SET 1.
Press + or – 3 to select “ RETURN” and press
SELECT/SET 1 twice. The Menu Screen closes.
There is the sound effect of a shutter closing.
NOTES:
● To remove the shutter sound, ੬ “BEEP” on pg. 23.
● If Snapshot recording is not possible, “PHOTO”
^ blinks
when SNAPSHOT
5 is pressed.
● If Programme AE with special effects (
੬ pg. 16) is
engaged, certain modes of Programme AE with special
effects are disabled during Snapshot recording. In such a
case, the icon blinks.
● If SNAPSHOT 5 is pressed when “DIS” is set to “ON”
(
੬ pg. 22), the Stabiliser will be disabled.
● During tape playback as well, all snapshot modes are
available. However, the shutter sound is not heard.
● During Snapshot recording, the image displayed in the
viewfinder may be partially missing. However, there is no
effect in the recorded image.
● When a cable is connected to the S/AV connector
#, the
shutter sound is not heard from the speaker, however it is
recorded onto the tape.
Auto Focus
The camcorder’s Full Range AF system offers
continuous shooting ability from close-up (as close as
approx. 5 cm to the subject) to infinity.
However, correct focus may not be obtainable in the
situations listed below (in these cases use manual
focusing):
•When two subjects overlap in the same scene.
•When illumination is low.*
•When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-colour
wall, or a clear, blue sky.*
•When a dark object is barely visible in the viewfinder.*
•When the scene contains minute patterns or identical
patterns that are regularly repeated.
•When the scene is affected by sunbeams or light
reflecting off the surface of a body of water.
•When shooting a scene with a high-contrast back-
ground.
*The following low-contrast warnings appear blinking:
, , and
NOTES:
● If the lens is smeared or blurred, accurate focusing is not
possible. Keep the lens clean, wiping with a piece of soft
cloth if it gets dirty. When condensation occurs, wipe with
a soft cloth or wait for it to dry naturally.
● When shooting a subject close to the lens, zoom out first
(
੬ pg. 12). If zoomed-in in the auto focus mode, the
camcorder may automatically zoom out depending on the
distance between the camcorder and the subject. This will
not occur when “TELE MACRO” (
੬ pg. 22) is activated.
SNAPSHOT RECORDING
1 Press SNAPSHOT 5. “PHOTO” ^ appears while
the snapshot is being taken.
If you press during Record-Standby . . .
..... “PHOTO” ^ appears and a still image will be
recorded for approx. 6 seconds, then the
camcorder re-enters the Record-Standby mode.
If you press during Recording . . .
..... “PHOTO” ^ appears and a still image will be
recorded for approx. 6 seconds, then the normal
recording resumes.
•Regardless of the Power Switch 8 position (“ ” or
“ ”), Snapshot recording takes place using the
selected Snapshot mode.
Motor Drive Mode
Keeping SNAPSHOT 5 pressed provides an effect
similar to serial photography. (Interval between still
images: approx. 1 second)
FULL
Snapshot mode
with no frame
FRAME
Snapshot mode
with frame
PIN-UP
Pin-Up mode
01 DX55/45/35/25EK_EN 16-23 03.1.23, 1:44 PM18