Filter
Top Products
7
ⅷ To save energy, when it is not being used turn
the system’s power off.
ⅷ This camera has been designed for indoor
use. It cannot be used outdoors.
ⅷ Do not install or use the camera in the
following places.
●In a place exposed to rain or moisture.
●In a place with vapor or oil soot, for example in
a kitchen.
●In a temperature outside the operating
temperature range (-10 f to 50 f).
●Near a source of radiation, X-rays, strong
radio waves or magnetism.
●In a place where corrosive gasses are
generated.
●In a place subject to vibration.
●In a place with excessive dirt.
●In an environment where there is cold air or
near the air outlet of an air conditioner.
ⅷ If this camera and the cables connected to this
camera are used where there are strong
electromagnetic waves or where there is
magnetism present, for example near a radio
or TV transmitter, power transformer or an
electric motor, the picture may produce noise
and the colors may be affected.
ⅷ This camera incorporates an AGC circuit. As a
result, when it is used under low light
conditions, the camera sensitivity is
automatically boosted and the picture may
look uneven. This is not a malfunction
however.
ⅷ When this camera is used in the ATW mode,
the recorded colors may be slightly different
from the actual colors due to the operational
principles of the auto-tracking white balance
circuit. This is however not a malfunction.
ⅷ If a high-intensity object (such as a lamp) is
shot, the image on the screen may have
vertical lines (smear) or blur (blooming) at its
periphery. This is a characteristic of the CCD,
and is not a defect.
ⅷ Observe the following when carrying out
camera maintenance.
●Turn the power OFF before proceeding to
carry out maintenance.
●Clean the dome cover lens using a lens wiper
cloth (or a tissue). If it is contaminated
seriously, clean the contaminated part with a
cloth (or a tissue) which has been soaked in a
solution of water and a neutral detergent.
ⅷ If the DAY/NIGHT switch is turned on, the
mode changes automatically to black and
white in dark places. As the sensitivity
increases, the image may look grainy and
white spots may appear.
When changing modes, bright portions of
image may be emphasized but this is not a
failure of the camera.
ⅷ When the supply voltage of the camera is low,
the input protection circuit within the camera
may be triggered and the power of the camera
may turn off automatically. Make sure to use a
supply voltage for the camera that is within -10
% of the rated voltage.)
ⅷ Upon switching between the HOME and
ALARM positions, the camera focus may
change slightly after the zoom operation
comes to a stop. This is due to the built-in
lensperformance and is not a malfunction.
(TK-C215V12 only)
ⅷ When the camera is moved from a cold area
to room temperature, condensation may occur
causing the camera to malfunction as a result.
In this case, turn on the power after waiting for
a few hours.
ⅷ This unit enlarges the rotation angle to
support wide range set up.
When the zoom of the lens is set to WIDE end
and the tilt angle is set around ±80Њ,the dome
cover can be visible into the image depending
on the rotation angle.
In this case, adjust the image angle if
necessary. (A pg. 23)
ⅷ All Interconnecting Equipment must be UL
Listed.
Operating Precautions
ⅥNote on consumable parts
(TK-C215V12 only)
The following parts are consumable and
should be replaced after a certain number of
hours or a count of operations.
The service lives given below are only typical
values. They may vary depending on the
operating environment and conditions. Note
that the replacement of consumable parts is
chargeable even when
they are replaced before the termination of the
warranty period.
●Zoom lens assembly
Zooming operation: 2 million times
TK-C215V4_V12_EN.book Page 7 Wednesday, August 2, 2006 1:18 PM