Filter
Top Products
102
The underlining in the variable range column indicates the setting in the preset
mode.
Chapter 7 Menu description tables
(continued)
7-2 SYSTEM SETTING
7-2-1 SYSTEM MODE
Item
Variable
range
Remarks
SYSTEM MODE
For AJ-HDX900E
For AJ-HDX900P
1080-50i
1080-59.94i
720-50P
720-59.94P
For setting the system frequency and the
recording format of the unit.
When this item is switched, turn “OFF” the
POWER switch on the unit and then turn it
“ON” again.
OWhen the remote control unit (AJ-RC10G)
is connected, this item is not displayed.
To switch this item, operate the main unit
independently.
CAMERA MODE
For AJ-HDX900E
For AJ-HDX900P
(1080-50i)
50i
25P
(1080-59.94i)
60i
30P
24P
24PA
(720-50P)
50P
25P
(720-59.94P)
60P
30P
24P
For setting the video system for shooting.
CUF
CUFR
TAKE TOTAL TIME NONE
:
5day
For setting the time required for shooting.
Select a setting from NONE (shooting
continues until it is stopped manually) to
5DAY (5 days).
Item
Variable
range
Remarks
REC TIME
For 59.94 Hz
For 50 Hz
00s01f
:
59s29f
00s01f
:
59s24f
For setting the recording time (one cut).
OWhen the CAMERA MODE item is set to
24P or 24PA, the value is set in
increments of 5 frames (rounded down).
(Minimum value: 00s05f)
PAUSE TIME
For 59.94 Hz
For 50 Hz
00h00m00s01f
:
00h04m59s29f
:
23h59m59s29f
00h00m00s01f
:
00h04m59s24f
:
23h59m59s24f
For setting the recording pause time.
OWhen the CAMERA MODE item is set to
24P or 24PA, the value is set in
increments of 5 frames (rounded down).
(Minimum value: 00h00m00s05f)
TOTAL REC TIME 00m00s01f
:
99m59s29f
OVER
100min
NONE
For displaying the total recording time. The
setting for this time cannot be changed.
The total time yielded by adding the REC
TIME, PAUSE TIME and TOTAL TAKE
TIME is displayed.
OThis indication is just a guide for the
recording time. It is impossible to record
for a period longer than the recording time
of the tape.
AUDIO REC OFF
ON
For setting the availability of audio records
during INTERVAL REC.
START DELAY 0SEC
:
10SEC
For setting the time taken until recording is
to start after the REC START button is
pressed in the INTERVAL REC mode.
PRE REC MODE OFF
ON
For setting the PRE RECORDING function.
OFF: Recording starts about 0.4 seconds
after pressing the REC START button
or the VTR button on the lens.
ON: The PRE RECORDING function is
activated.
For details, refer to “3-4 To record video
signals of a few seconds before starting
recording (PRE-RECORDING function).”
RETAKE MODE ON
OFF
For setting the RETAKE function.
ON: The RETAKE function is activated.
OFF: The RETAKE function is not activated.
It returns to OFF once the power is turned
off.
For details, refer to “3-6 To take the previous
cut again (RETAKE function).”
CUF
CUF
CUF
CUF
CUF
PRE REC TIME 0SEC
:
7SEC
For setting the length of time for which the
video and audio signals can be recorded
before the REC START button is pressed in
PRE RECORDING.
CUF
CUF
F
7-2-2 REC FUNCTION
Item
Variable
range
Remarks
INTERVAL REC
MODE
ON
ONE SHOT
OFF
For setting the INTERVAL REC function.
ON:
For executing the interval recording.
It is possible to record in intervals in
increments of one frame.
ONE SHOT:
Recording is performed only once for the
time set in the REC TIME item, after
which it stops.
OFF:
Interval recording is not performed.
For details, refer to “3-5 Recording in
intervals (INTERVAL REC function).”
CUF
INTERVAL REC
HOLD
ON
OFF
For setting whether the settings in the
INTERVAL REC MODE item are retained or
released, when the power is turned OFF.
ON: For retaining the settings in the
INTERVAL REC MODE item.
OFF: For releasing the settings in the
INTERVAL REC MODE item.
CUF
<Note>
If the SYSTEM MODE item is changed while the time code is
advanced in the free-run mode (the TCG switch is set to the
F-RUN position.), the time code may not record properly.
When the SYTEM MODE item is changed and the power of
the unit is turned on again, check the time code and set it
again if necessary.