Filter
Top Products
Pan/Tilt Head Controller AW-RP400
28 (E)
ENGLISH
Menu settings
OPTION SWITCH A to H settings
(NOT USE / DEFROSTER / WIPER / HEATER/FAN / AUTO FOCUS / ND / OPTION / EXTENDER)
The following functions can be allocated to OPTION buttons A to H. Different functions can be allocated for different pan/tilt
heads.
NOT USE: The button is disabled.
DEFROSTER: This controls the ON and OFF states of the defroster function when using a pan/tilt head system
equipped with this function.
Each time the button is pressed, ON is switched to OFF or vice versa.
When the defroster function is ON, the lamp of the button to which this function has been allocated is lit;
when it is OFF, the lamp is off.
WIPER: This controls the ON and OFF states of the wiper function when using a pan/tilt head system equipped
with this function.
Each time the button is pressed, ON is switched to OFF or vice versa.
When the wiper function is ON, the lamp of the button to which this function has been allocated is lit;
when it is OFF, the lamp is off.
HEATER/FAN: This controls the ON and OFF states of the heater/fan function when using a pan/tilt head system
equipped with this function.
Each time the button is pressed, ON is switched to OFF or vice versa.
When the heater/fan function is ON, the lamp of the button to which this function has been allocated is
lit; when it is OFF, the lamp is off.
OPTION: This controls the short-circuit and open-circuit states of the AC adaptor’s OPTION CONTROL OUT
connector when using an AC adaptor for a pan/tilt head system equipped with the OPTION switch
control function.
Each time the button is pressed, short circuit is switched to open circuit or vice versa.
When short-circuited, the lamp of the button to which this function has been allocated is lit; when open-
circuited, the lamp is off.
ND: This controls the ON and OFF states of the ND filter when using a lens equipped with an ND filter. Each
time the button is pressed, ON is switched to OFF or vice versa.
When the ND filter is ON, the lamp of the button to which this function has been allocated is lit; when it is
OFF, the lamp is off.
EXTENDER: This controls the ON and OFF states of the extender when using a lens equipped with an extender.
Each time the button is pressed, ON is switched to OFF or vice versa.
When the extender is ON, the lamp of the button to which this function has been allocated is lit; when it
is OFF, the lamp is off.
AF: This controls the ON and OFF states of the auto focus function when using a lens equipped with this
function.
Each time the button is pressed, ON is switched to OFF or vice versa.
When the auto focus function is ON, the lamp of the button to which this function has been allocated is
lit; when it is OFF, the lamp is off.
MEMORY LENGTH setting (60s/120s/300s/600s)
This menu item is used to set the tracing memory data recording time and the number of memories.
60s : 60 sec. ! 10 memories
120s : 120 sec. ! 5 memories
300s : 300 sec. ! 2 memories
600s : 600 sec. ! 1 memory
≥ When data has already been registered in a tracing memory, the setting for the recording time and number of memories
cannot be changed. To reset a setting, delete the registered data in the tracing memory first.
CONTROL SELECT MODE setting (INTERLOCK/UN-INTERLOCK)
This menu item is for selecting the method used to select the pan/tilt head and camera when the AW-CB400 remote
operation panel has been connected to the AW-RP400 controller.
INTERLOCK: When the pan/tilt head and camera system are selected by the AW-RP400 or AW-CB400, the same
system is selected by the other unit as well.
UN-INTERLOCK: A different pan/tilt head and camera system can be selected by the AW-RP400 and AW-CB400.