Filter
Top Products
46
(Red): While Moving Picture(MPEG4) recording is
activated
(Red): No Card (MPEG4 Mode)
(Green): While the card is being read, MPEG4
recording operation is not possible
(Blue): Voice Recording Mode
(Red): While Voice Recording is activated
(Red): No Card (Voice Recording Mode)
(Green): While the card is being read, Voice
recording operation is not possible
ß
ßß
ß
: Video Flash (setting to “Normal”)
ß
ßß
ß
i: Video Flash (setting to “i”)
ß
ßß
ß
j: Video Flash (setting to “j”)
ªTo Change the Counter Display Mode
By changing [C.DISPLAY] on the [DISPLAY SETUP]
Sub-Menu, you can change the Counter Display Mode to
Tape Counter Indication [COUNTER] (0:00.00), Memory
Counter Indication [MEMORY] (M0:00.00), and Time Code
Indication [TIMECODE] (0h00m00s00f). (l 13) By
repeatedly pressing the [COUNTER] Button on the Remote
Controller, you can change the Counter Display Mode.
ªTo Display Date/Time Indication
To display Date/Time Indication, set the appropriate Date/
Time in [DATE/TIME] on the [DISPLAY SETUP] Sub-Menu.
(l 13)
You also can press the [DATE/TIME] Button of the Remote
Controller repeatedly to display or change the Date/Time
Indication.
ªTo Change the Display Mode
By changing [DISPLAY] on the [DISPLAY SETUP]
Sub-Menu, you can change the Display Mode to All Function
Display [ALL], Partial Display [PARTIAL], and Minimum
Display [OFF].
~~~~~~~~~~~~~~~~~~~
Owner ID
Youcan register your name and address in your Movie
Camera to identify the owner.
1
Set [CAMERA FUNCTION] >> [OTHER
FUNCTION] >> [OWNER ID SET] >> [YES].
≥The Owner ID setup screen appears.
2
Turn the [PUSH] Dial to select [PIN NUMBER]/
[NAME]/[HOUSE No.]/[POST CODE] and press
the [PUSH] Dial to enter the setup mode.
3
Turn the [PUSH] Dial to select characters and
press the [PUSH] Dial to enter them.
≥You can input 4 digits in [PIN NUMBER], up to 12
characters in [NAME], and up to 11 characters in
[HOUSE No.] and [POST CODE].
4
Press the
[∫]
Button to exit the setup mode.
To Check Owner ID
If Owner ID has already been set, carrying out Step1 above
will display [INPUT PIN NUMBER] on the screen. Input the
Pin Number you have already selected. If the number is not
correct, the screen will not change. If the number is correct,
the contents of the setup will be displayed. (By repeating
Steps 2 to 4 above, you can change the contents.)
~~~~~~~~~~~~~~~~~~~
Warning/Alarm Indications
If any one of the following indications lights up or flashes,
please check the condition of the Movie Camera.
≥Some Indications may not be displayed according to the
model.
3: Condensation has occurred. (l 52)
Y: The accidental erasure prevention
slider on the inserted Cassette is
open (that is, set to [SAVE]).
You are about to do audio dubbing
on the unrecorded (blank) portion of
the tape.
No Cassette is inserted. (l 11)
6: The Battery is low. Recharge it.
(l 10)
0: The button-type battery is low or not
in. (l 17)
:: The video heads are dirty. (l 52)
2END: The tape came to end during
recording.
REMOTE: Wrong Remote Controller Mode has
been selected. (l 9)
PRINTER ERROR: The Video Printer is not connected
correctly, or the Video Printer is not
functioning properly.
UNPLAYABLE TAPE
(OTHER FORMAT): You are attempting to play back a
tape section that has been recorded
with a different TV system.
UNABLE TO A. DUB
(LP RECORDED): Because the original recording was
done in LP Mode, audio dubbing
cannot be performed.
INCOMPATIBLE
TAPE: This Cassette is incompatible.
PLEASE RE-OPERATE
AFTER PUSHING
RESET BUTTON: Mechanism Irregular is detected.
Press the [RESET] Button (l 8).
This may solve the problem.
TO SERVICE: It is a malfunction.
CARD FULL: Card does not have sufficient
memory remaining.
NO CARD: Card is not inserted.
NO PICTURE: Card has no pictures recorded on it.
NO MPEG4: Card has no moving pictures
(MPEG4) recorded on it.
NO VOICE DATA: Card has no voice data recorded on
it.
CARD ERROR: This Card is not compatible with this
Movie Camera.
COPY INHIBITED: Because the medium is protected by
a copy guard, images cannot be
recorded correctly.
~~~~~~~~~~~~~~~~~~~
Notes and Hints
ªConcerning the Power Supply
≥When the Movie Camera is used for a long time, the
Camera body becomes warm, but this is not a malfunction.
≥If the [CHARGE] Lamp does not light up although the
Battery is attached to AC Adaptor, detach the Battery and
reattach it.
≥Battery CGP-D110 and CGP-D105 cannot be charged with
this AC Adaptor.
ªInserting/Removing the Cassette
≥In the case of using a previously recorded Cassette, you
can use the Camera Search Function to find the position
where you want to continue recording.
≥If a new Cassette is inserted, rewind to the beginning of the
tape before starting recording.
≥When inserting the cassette, make sure it faces in the right
direction and then push it in until it stops.
UXGA
UXGA
UXGA
UXGA
V
OICE
UXGA
V
OICE
UXGA
UXGA