56
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
■ AUDIO RECORDING
This unit can record audio in one channel along with the
video. When recording audio, the continuous recording
time is less than when recording only video.
<INITIAL SET UP/INFORMATION>
HDD SETTINGS
>>
AUDIO RECORDING OFF
REAR TERMINAL SETTINGS
COMMUNICATION PORT SETTINGS
CAMERA CONTROL
INFORMATION/SERVICE
PASSWORD
LANGUAGE SELECTION
Setting ( default : “OFF” )
“ON” : Records video and audio.
“ALARM” : During alarm recording or emergency re-
cording, records video and audio.
“OFF” : Does not record audio.
1. Press the SET UP button
}
<SETTINGS>
}
Select “AUDIO
RECORDING” in the <INITIAL SET UP/INFORMATION>
screen. Display the desired setting and confirm.
2. Turn the SHUTTLE ring counterclockwise or press the SET
UP button to exit.
When setting “AUDIO RECORDING” to “ON”, a
speaker display (
) appears to the right of recordable
time display in the <RECORD SETTING> and <RECORD
SETTING A> ~ <RECORD SETTING D> screens.
<RECORD SETTING> 2/2
<RECORD SETTING> ALARM
NO PPS GRADE A-PPS A-GRADE
>>
1.875P STD 1.875P STD
1.875P STD 1.875P STD
1.875P STD 1.875P STD
1.875P STD 1.875P STD
1.875P STD 1.875P STD
1.875P STD 1.875P STD
1.875P STD 1.875P STD
PRE ALARM REC ( S ) S
SHUTTLE<<:BACK
<ESTD REC> D H M
10
11
13
14
15
16
12
Even when setting “AUDIO RECORDING” to “ON”,
audio cannot be recorded for the following settings.
• Audio recording cannot be performed when “PPS” of
“RECORD SETTING” are all set to smaller than
“0.333P” when setting normal recording. In this case,
( X ) appears to the right of recordable time display.
• When the camera selection during alarm recording is
as follows :
“ALARM” : “A-PPS” of all cameras set for alarm re-
cording are set to smaller than “0.333P”.
“ALARM PLUS” : “PPS” and “A-PPS” of all cameras
set for normal recording and alarm recording are set to
smaller than “0.333P”.
■ REAR TERMINAL SETTINGS
♦ MODE OUT 1 ~ MODE OUT 5
The unit status can be outputted from the MODE OUT termi-
nals on the rear. There are 5 MODE OUT terminals and each
terminal can be set to generate a certain type of output.
<REAR TERMINAL SETTINGS>
>>
MODE OUT 1 OFF
MODE OUT 2 OFF
MODE OUT 3 OFF
MODE OUT 4 OFF
MODE OUT 5 OFF
KEY SOUND ON
BUZZER OFF
REMAIN HDD MAIN-10
%
CALL OUT SETTINGS
EMERGENCY REC DURATION 10M
Setting ( default : “OFF” )
“REC” : Outputs signals during recording.
“PLAY” : Outputs signals during playback.
“REMAIN” : Outputs signals when the remaining HDD
device or archive device space reaches the value speci-
fied in “REMAIN HDD”.
“POWER” : Outputs signals when the power of the unit
turns on.
“MOTION1” ~ “MOTION5” : Outputs the camera num-
bers detected during motion detection recording using
binary notation (MODE OUT 1 ~ MODE OUT 5 are
linked). The last motion detection triggered is main-
tained for 2 seconds.
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
O : Signal is outputted.
X : No signal is outputted.
MODE OUT terminals
1
O
X
O
X
O
X
O
X
O
X
O
X
O
X
O
X
4
X
X
X
X
X
X
X
O
O
O
O
O
O
O
O
X
3
X
X
X
O
O
O
O
X
X
X
X
O
O
O
O
X
5
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
2
X
O
O
X
X
O
O
X
X
O
O
X
X
O
O
X
Relation between a camera number and a MODE OUT output
“ALARM” : Outputs signals during alarm recording.
“OFF” : No signal is outputted.
Capacity warning from MODE OUT is only outputted
during recording.
1. Press the SET UP button
}
<SETTINGS>
}
<INITIAL SET
UP/INFORMATION>
}
Select “REAR TERMINAL SETTINGS”
screen.
2. From the 5 MODE OUT terminals, display the desired setting
for the terminal (MODE OUT 1 ~ MODE OUT 5) to output
signals and then confirm.
3. To set other terminals, repeat step 2.
4. Turn the SHUTTLE ring counterclockwise or press the SET
UP button to exit.
♦ KEY SOUND
It is possible for the unit to make button buzzer sounds
when using the operation buttons on the front of the unit
or when operating the JOG dial or SHUTTLE ring.
<INITIAL SET UP/INFORMATION> (continued)
