Filter
Top Products
- 11 -
PRECAUTIONS FOR USE AND INSTALLATION
* Never aim the camera at the sun.
Never aim or point the camera at the sun even if you
are not shooting.
* Do not shoot intense light.
Strong light such as a spot light on the image plane will
cause blooming or smear. When strong light comes into
the image plane, vertical stripes may appear on it.
However, this does not mean that the camera is defect.
* Take precautions when handling a camera.
Do not drop your camera, or give it a strong shook or
vibration. This may cause camera to malfunction.
* Do not touch internal parts.
Be sure not to touch the internal parts. This may cause
to electrical shock.
* Do not let the camera get wet.
Install the camera at the place where it will not get wet.
Should it gets wet, turn off the power immediately and
contact your dealer.
* Install your camera where no video noise appears.
When camera cables have been laid near electric wires
or television receivers, a noise may interfere the image.
If noise occurs, relocate cables or reinstall equipment.
* Check the ambient temperature and humidity.
Avoid using camera in areas where temperature is
consistently hotter or colder than the specified range
(See Specifications chart below) or poor image quality
or damaged parts may occur. Precautions should also
be taken to avoid areas of high humidity.
* Should you notice any trouble.
If any trouble occurs while you are using the camera,
turn off the camera and contact your dealer. Failure to
do so may cause damage to the camera.
* The socket-outlet should be installed near the
equipment and should be easily accessible.
* Do not place this video product on an unstable cart,
stand, tripod, bracket, or table. The video product may
fall, causing serious injury to a child or adult, and serious
damage to the appliance. Use only with stand, tripod,
bracket, or table recommended by the manufacturer, or
sold with the video product. Any mounting of the
appliance should follow the manufacturer's instructions,
and should use a mounting accessory recommended by
the manufacturer.
* This video product should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supply to your location,
consult your appliance dealer or local power company.
* Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords at
plugs, screws, and the point where they exit from the
appliance.
* Do not overload power supply and extension cords, as
this can result in a risk of fire or electric shock.
* Never push objects of any kind into this video product
through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or
electrical shock. Never spill liquid of kind on the video
product.
* When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or that have the same characteristics as the
original parts. Unauthorized substitutions may result in
fire, electric shock or other hazards.
* Upon completion of any service or repairs to this video
product ask the service technician to perform safety
checks to determine that video product is in proper
operating condition.
6X1NSBA02 Printed in CHINA
ELMO (Europe) G.m.b.H.
Neanderstr. 18
40233 Dusseldorf,
Germany
Tel.
0211-376051-53
Fax. 0211-376630
E-mail:elmoeurope@AOL.com
Web:http://www.elmo.de/
ELMO Mfg. Corp.
1478 Old Country Road,
Plainview, NY 11803-5034
U.S.A.
Tel.
516-501-1400
Fax. 516-501-0429
E-mail:elmo@elmousa.com
Web:http://www.elmousa.com/
ELMO Canada Mfg. Corp.
44 West Drive, Brampton,
Ontario, L6T 3T6,
Canada
Tel.
905-453-7880
Fax. 905-453-2391
E-mail:info@elmocanada.com
Web:http://www.elmocanada.com/
ELMO CO., LTD.
6-14, Meizen-cho, Mizuho-ku,
Nagoya, 467-8567 Japan
OVERSEAS SUBSIDIARY COMPANIES