Filter
Top Products
GV44…, GV45…, GV46… Allgemeiner Teil / General
GRUNDIG Service-Technik 1 - 53
Possible messages in the dialogue line
If the "Remaining time" is negative (–) and highlighted in red,
then a cassette of insufficient playing time has been loaded,
or the sum of all TIMER recordings is too large.
If the message "Record period" appears instead of
"Remaining playing time," then...
... no cassette is loaded;
... the cassette is protected against new recording and will be
automatically ejected.
... the playing time of the cassette was not recognized.
If a red line with the message "Record Timer Overlap" appears
(the corresponding TIMER positions are highlighted in red),
then the recording times of the TIMER positions overlap.
In this case, change the data of one TIMER position by
pressing the
“
(green) button and selecting the timer
position with the
W
or
Q
button.
Select the data to be changed with the
E
or
R
button,
enter the new data, and confirm the data lines step by step
with the
O
button.
When you are still in the "Record Programming" mode, the
message "Record beginning soon" will appear ten minutes
before the beginning of the recording.
If the message "Record start time has passed" appears, then
you must immediately exit the record programming mode so
that the recorder can start recording.
In order to do so, press the
©
(TIMER) button.
Modifying individual data items of a TIMER posi-
tion
Select the "Info" menu by pressing the
ø
button.
Select the "Record Programming" menu by pressing the num-
bered button
1
, and then press the
“
(green) button.
Select the respective TIMER position by pressing the
W
or
Q
button.
Select the data item to be modified by pressing the
E
or
R
button, enter the new data with the numbered buttons
1
...
0
, and confirm the data lines step by step with the
O
button.
Clearing TIMER positions
Select the "Info" menu by pressing the
ø
button.
Select the "Record Programming" menu by pressing the num-
bered button
1
, and then press the
“
(green) button.
Select the TIMER position to be cleared with the
W
or
Q
button and clear it by pressing the
ƒ
button.
The TIMER position is cleared and can be programmed again.
Interrupting the record stand-by mode of the
recorder
If you have programmed TIMER positions but wish to use the
recorder while it is in record stand-by mode, then:
press the
>
button on the recorder, the cassette is automa-
tically ejected,
or
press the
©
(TIMER) button.
The TIMER data disappears from the display of the recorder
and the TIMER display flashes.
Now select the desired function.
Reactivating the record stand-by mode of the
recorder
Insert a cassette with sufficient playing time, wait until the
tape measurement is completed, and then press the
©
(TIMER) button.
The remaining playing time will appear briefly in the display
of the recorder.
The recorder is once again in the record stand-by mode and
the TIMER recordings will be made at the programmed times.
The record stand-by mode of the recorder is now inter-
rupted.
6.2 Record Programming 6.3 Record Programming on the set
Programming with the Buttons and
the Display of the Recorder,
Preparation
Insert a cassette with sufficient playing time which is not pro-
tected against new recording.
Open the left flap on the recorder.
MIC L R
AUDIO IN VIDEO IN / CV
y
MAN DUBBING
INSERT
RECORD LEVEL
S
-
VHS
y
OK
CL
SET CHECK EW/EDON/OFF
TIMER
Press these buttons on the
recorder
Ǽ
You will see this in the display of
the recorder Explanations
1. Starting programming
v
The recorder is ready for data entries.
Programme position (TV station) 1 is
displayed, BBC I in the example.
You can "overwrite" the selected data as
long as this entry position is flashing.
If all of the TIMER positions are occu-
pied,
»TIMER FULL«
will appear briefly
in the display.
If the recorder does not accept the
data, e.g. stop time is equal to the
start time, the first entry position of
the data to be corrected flashes
again.
ŁŁ
You cannot programme recordings in the long-play mode or
programme broadcasts from the satellite receiver.
2. Selecting a programme
Sor A
¢
OK
.
The programme positions will be selec-
ted in the following order: 1, 2 to 59,
60, CV, HI, A1 or A2.
The current date is shown, the 19th in
the example.
BBC I --:--I -- :--
PROG
SEC PAL
SAT
START
C +
DATE
STOP
VPS
PDC
888888 88:88I9 88:88:88
PROG
SEC PAL
SAT
START
C +
DATE
STOP
VPS
PDC