Filter
Top Products
EN 63
Master Page: Right
Select Scenes
6 Press PLAY (U) and then press R.A.EDIT ON/OFF
on the remote control.
The Random Assemble
Editing Menu appears.
7 For GR-DV900 owners:
If using a Wipe/Fader at
the beginning of the
scene, press FADE/WIPE
on the remote control.
● Cycle through the
effects by pressing
repeatedly, and stop when the one you want is
displayed.
● You cannot use a Picture Wipe/Dissolve at the
beginning of Program 1.
8 At the beginning of the scene, press EDIT IN/
OUT or IN/OUT on the remote control. The Edit-
In position appears in the Random Assemble
Editing Menu.
9 At the end of the scene, press EDIT IN/OUT or
IN/OUT. The Edit-Out position appears in the
Random Assemble Editing Menu.
10 For GR-DV900 owners: If using a Wipe/Fader
at the end of the scene, press FADE/WIPE.
● Cycle through the effects by pressing
repeatedly, and stop when the one you want is
displayed.
● If you select a Wipe/Fader effect for an Edit-Out
point, the effect is automatically applied to the
following Edit-In point.
● You cannot use a Picture Wipe/Dissolve at the
end of the last scene.
● When you use Fader/Wipe effects, that time is
included in the total time (this does not apply
to Picture Wipe/Dissolve.)
11 For GR-DV900 owners: If using Playback
Special Effects, press EFFECT. (੬ pg. 58)
12 Repeat steps 8 through 11 to register
additional scenes.
● To change previously registered points, press
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
● If you are not using Wipe/Fader (GR-DV900
only) or Program AE with special effects, repeat
steps 8 and 9 only.
NOTES:
● When choosing a scene, set Edit-In and Edit-Out
points so that there is a relatively large difference
between them.
● If the search time for an in-point exceeds
5 minutes, the recording deck’s Record-Standby
mode will be cancelled and editing will not take
place.
● If there are blank portions before or after the Edit-
In and Edit-Out points, a blue screen may be
included in the edited version.
● Since time codes register time only as accurately
as seconds, the time code total time may not
match the total program time exactly.
● Turning off the camcorder’s power erases all
registered Edit-In and Edit-Out points.
● For GR-DV900 owners: If you select Sepia or
Monotone mode from Program AE with special
effects, you cannot use the Dissolve or Black &
White Fader. In this case the Dissolve or Black &
White indicator begins blinking. Once the next
Edit-In point is registered, the effect is turned off.
To combine these effects, use Sepia or Monotone
during recording, then use the Dissolve or Black &
White Fader during Random Assemble Editing.
● For GR-DV900 owners: It is not possible to use
Wipe/Fader effects and Program AE with special
effects during Random Assemble Editing using a
DV cable.
PLAY
R.A.EDIT
ON/OFF
EFFECT
FADE/WIPE
EDIT IN/OUT
CANCEL
REW
FF
ON/OFF
IN/OUT
RM-V717U (provided
with GR-DV900 only)
RM-V700U
(optional)
1
2
3
4
5
6
7
8
––:–– ~
~
~
~
~
~
~
~
–
–
:
––
0
:
000
––
TOTAL
CODETIME
NIOUT
MODE
Selected parameter
CONTINUED ON NEXT PAGE
ADVANCED FEATURES
GR-DV900US.book Page 63 Monday, January 6, 2003 4:21 PM