Filter
Top Products
21
8-1. Gamma Correction (GAMMA)
1. Move the cursor to the GAMMA parameter. The “I” cur-
sor starts blinking.
2. While observing the waveform monitor or the color
video monitor, adjust the gamma level.
When the “I” cursor is at the end of the “+” side,
gamma correction is set to OFF.
When the “I” cursor is at the end of the “−” side, black
strech (BLACK STRET) is set.
8-2. Auto Knee ON/OFF (AUTO KNEE)
1. Move the cursor to the AUTO KNEE parameter.
2. Select ON or OFF for the auto knee mode.
8-3. Total Pedestal Level Control (TOTAL-PED)
1. Move the cursor to the TOTAL-PED parameter. The “I”
cursor starts blinking.
2. While observing the waveform monitor or the color
video monitor, adjust the total pedestal level (black
level).
Move the “I” cursor to the “+” side to make the image
brighter.
Move the “I” cursor to the “−” side to make the image
darker.
8-4. Chrominance Level Control (CHROMA GAIN)
1. Move the cursor to the CHROMA GAIN parameter. The
“I” cursor starts blinking.
2. While observing the waveform monitor or the color
video monitor, adjust the chroma level.
8-5. Detail Band Control (DTL BAND)
1. Move the cursor to the DTL BAND parameter. The “I”
cursor starts blinking.
2. While observing the color video monitor, adjust the
aperture level.
Move the “I” cursor to the “+” side to raise the frequen-
cy.
Move the “I” cursor to the “−” side to lower the frequen-
cy.
8-6. Horizontal Detail Gain Control (HDTL GAIN)
1. Move the cursor to the HDTL GAIN parameter. The “I”
cursor starts blinking.
2. While observing the color video monitor, adjust the
aperture level.
Move the “I” cursor to the “+” side to make the image
sharper.
Move the “I” cursor to the “−” side to make the image
softer.
When the “I” cursor is at the end of the “−” side, the
horizontal detail level is set to OFF.
8-7. Vertical Detail Gain Control (VDTL GAIN)
1. Move the cursor to the VDTL GAIN parameter. The “I”
cursor starts blinking.
2. While observing the color video monitor, adjust the
aperture level.
Move the “I” cursor to the “+” side to make the image
sharper.
Move the “I” cursor to the “−” side to make the image
softer.
When the “I” cursor is at the end of the “−” side, the
vertical detail level is set to OFF.
8-8. Red Detail ON/OFF (RED DTL)
1. Move the cursor to the RED DTL parameter.
2. Select ON or OFF for the RED DTL mode.
When ON is selected, the red detail is enhanced.
8-9. Clear Digital Noise Reduction Control
(CLEAN DNR)
1. Move the cursor to the CLEAN DNR parameter.
2. Select OFF, LOW or HI for the CLEAN DNR mode.
8-10. 2 Dimention Low Pass Filter (2D LPF)
1. Move the cursor to the 2D LPF parameter.
2. Select ON or OFF for the 2D LPF mode.
8-11. 6 Chroma Matrix Controls
(MATRIX R-G)
(MATRIX R-B)
(MATRIX G-R)
(MATRIX G-B)
(MATRIX B-R)
(MATRIX B-G)
1. Move the cursor to the desired matrix item. The “I” cur-
sor starts blinking.
2. While observing the vectorscope or the color video
monitor, adjust the matrix level.
8-12. Chroma Phase Control (HUE)
1. Move the cursor to the HUE parameter. The “I” cursor
starts blinking.
2. While observing the vectorscope or the color video
monitor, adjust the chroma phase (hue).
To reset to the factory setting
Any of the above settings except AUTO KNEE, RED DTL,
CLEAN DNR and 2D LPF, can be reset to the factory set-
tings.
Move the cursor to the desired item and press A and B
simultaneously for a second and more.