Samsung SC-D963 Camcorder User Manual


 
ENGLISH
ESPAÑOL
1616
Preparation Preparación
Using the Lithium Ion Battery Pack
Use SB-LSM80 or SB-LSM160 Battery Pack only.
The Battery Pack may be charged a little at the time of purchase.
Charging the Lithium Ion Battery Pack
1. Turn the [Power] switch
to [Off].
2. Attach the Battery Pack
to the Camcorder.
3. Connect the AC Power
Adapter to an AC Cord
and connect the AC
Cord to a wall socket.
4. Connect the DC cable to the DC jack on the Camcorder.
The charging indicator will start to blink, showing that the Battery is
charging.
5. Press and hold the DISPLAY button while charging
and the charging status will be displayed on the LCD
for 7 seconds.
Indicated battery level is given as reference data
for the user, it is the approximate. It may differ from
Battery capacity and temperature.
6. When the Battery is fully charged, disconnect the
Battery Pack and the AC Power Adapter from the
Camcorder. Even with the Power switched Off, the
Battery Pack will still discharge.
Charging/
Recording Times
based on Model
and Battery Type.
If you close the
LCD Screen, it
switches off and the
Viewfinder switches
on automatically.
The continuous recording times given in the table to the right are
approximations. Actual recording time depends on usage.
The continuous recording times in the operating instructions are
measured using a fully charged Battery Pack at 77 °F (25 °C).
Even when the Power switched Off, the Battery Pack will still
discharge if it is left attached to the device.
Battery
SB-LSM80
SB-LSM160
(Option)
Charging
time
Approx.
1hr 20min
Approx.
3hr
LCD On
Viewfinder On
Recording time
Time
Approx.
1hr 20min
Approx.
2hr 40min
Approx.
1hr 30min
Approx.
3hr
Blinking time
Once per second
Twice per second
Three times per second
Blinking stops and stays on
On for a second and off for
a second
Charging rate
Less than 50%
50% ~ 75%
75% ~ 90%
90% ~ 100%
Error - Reset the Battery
Pack and the DC Cable
Utilización de la batería de iones de litio
Utilice únicamente la batería B-LSM80 o SB-LSM160.
Es posible que la batería esté cargada sólo parcialmente al adquirir
la videocámara.
Carga de la batería
de iones de litio
1. Gire el interruptor
[Power] a [Off].
2. Conecte la batería a la
videocámara.
3. Conecte el adaptador
de CA a un cable de CA y éste a una toma de corriente.
4. Conecte el cable de CC al terminal de CC de la videocámara.
El indicador de carga comenzará a parpadear, lo cual indica que se
está cargando la batería.
5. Presione la tecla DISPLAY mientras se produce la
carga y el estado de carga aparecerá en la pantalla
LCD durante 7 segundos.
El nivel de la batería indicado que se facilita al usuario
son datos de referencia aproximados. Puede que
difiera de la capacidad y temperatura de la batería.
6. Cuando la batería esté totalmente cargada,
desconecte la batería y el adaptador de CA de la
videocámara. Incluso con la videocámara apagada,
la batería se descargará.
Tiempos de
carga/grabación
basándose en el
modelo y el tipo
de batería
Si cierra la pantalla
LCD, se apaga y el
visor se enciende
automáticamente.
Los tiempos de grabación continua que se facilitan en la tabla son
aproximados.
El tiempo real de grabación depende del uso de la videocámara.
Los tiempos de grabación continua en las instrucciones de
funcionamiento se miden utilizando una batería totalmente cargada a
25 °C (77 °F).
Incluso con la unidad apagada, la batería se descargará si se deja
conectada al dispositivo.
Frecuencia de parpadeo
Una vez por segundo
Dos veces por segundo
Tres veces por segundo
Deja de parpadear y queda encendido
Encendido durante un segundo
y apagado durante un segundo
Velocidad de carga
Menos del 50%
50% ~ 75%
75% ~ 90%
90% ~ 100%
Error – Reinicialice la
batería y el cable de CC
Battery Info
BBaatttteerryy cchhaarrggeedd
0% 50% 100%
Batería
SB-LSM80
SB-LSM160
(Opcional)
Tiempo de
carga
Aprox. 1 h.
20 min.
Aprox. 3 h.
LCD ENCENDIDA
Visor encendido
Tiempo de grabación
Tiempo
Aprox. 1 h.
20 min.
Aprox. 2 h.
40 min.
Aprox. 1 h.
30 min.
Aprox. 3 h.
0???? SCD963 USA+ESP ~048 2/21/06 8:41 PM Page 16