Filter
Top Products
C-RM500
REMOTE CONTROLLER
The C-RM500 Remote Controller is designed for use in camera-
based systems that allow remote control from up to 1.2km away
over RS-485 communication lines. It allows video images to be
switched remotely and can handle a maximum of 16 TOA's
Combination Dome Cameras when used together with the TOA
Multiplexer. Easy-to-see LEDs inform status of control, alarm, focus
and other functions.
Control up to 16 TOA's Combination Dome Cameras
Realtime control as well as preprogrammed position retrieval of
up to 255 positions is provided. Each position allows providing a
specific title as well remote image quality adjustment.
Instant position recall
The most used camera and position numbers can be assigned to
function keys A through H for one-touch instant recall. Other
camera numbers and position numbers can be assigned to ID
numbers from 1 through 512 and easily retrieved using the ten-
key pad.
Controls Multiplexer
The C-RM500 can also control the TOA multiplexers and allows
switching video image display modes – single screen, single
screen in sequence, 4-screens in sequence, as well as 4, 9, 10
and 16-segment split screens.
Alarm capability
Alarm signals received by the alarm input of combination dome
cameras can be transmitted to the C-RM500 via a pair of RS-485
communication line where the C-RM500’s alarm operations can
be activated, based on the alarm signal type received. This has
reduced the number of signal lines that were conventionally
required in an expanded system. An Alarm Hold function allows
temporarily suspending automatic switching of video images
triggered by an alarm to enable the operator to prioritise the
screen currently being viewed. In addition, the C-RM500 can
receive alarm signals from an C-AL80 unit through the
RS-232C port.
2 Location Control
The system can be independently controlled in two separate
locations by installing 2 C-RM500 units.
●
●
●
●
●
Power Source 12 V DC
Current Consumption 150 mA
Slave Remote Controller RS-485, screwless connector
Camera Control RS-485, screwless connector (*
1
)
Switcher Control RS-485, screwless connector
RS-232C, D-sub connector (9 pins, male)
Alarm Input RS-232C, D-sub connector (9 pins, male)
Alarm Output/ Alarm output: 16 channels, NPN open collector output,
Control Input withstand voltage: 30 V DC,
control current: 20 mA
Alarm input: 1 channel, no-voltage make contact input,
open voltage: 5 V DC,
short-circuit current: 5 mA max.
Home position selection input:
1 channel, no-voltage make contact input,
open voltage: 5 V DC, short-circuit current:
5 mA max.
D-sub connector (25-pins, female)
Display LED indication of control status, alarm status, alarm hold
status, still picture status, defroster, auxiliary setting, auto,
auto focus, and lens speed
LCD indication of key entry confirmation
Alarm Signal Continuous alarm tone (can be turned on and off)
Number of Unit Up to 2 (one to be set for MASTER unit, another for
Connections SLAVE unit)
Maximum Cable 1.2 km (*
2
) (between the Remote controller and the
Distance Combination cameras)
Operating Temperature 0°C to +50°C
Operating Humidity Under 90% RH (no due condensation produced)
Finish Panel: Surface-treated steel plate, sand gray, paint
Sides: Rubber
Dimensions 326 (W) × 62 (H) × 185.2 (D) mm
Weight 1.8 kg
Accessory D-sub connector (9 pins, male) × 1,
D-sub connector(25 pins, male) × 1
Applicable Model Combination dome camera: C-CC504S, C-CC554S
(option) Switcher: C-MS161D, C-MS91D
Slave remote controller: C-RM500
Interface unit: C-IF500
Alarm unit: C-AL80
(*
1
) Can connect up to 31 units mixing with combination cameras and interface units.
(*
2
) Applies to the system where the unit and combination camera are connected in a matched pair.
Represents the total of connected cable distances if multiple combination cameras or interface
units are connected in the system (when the CPEV-S cable thicker than 0.65 mm in diameter is used)
.
SPECIFICATIONS
APPEARANCE AND DIMENSIONAL DIAGRAM
Unit: mm
57.9
31.7
185.2
Figure of the installed unit
25
63.3
62
10˚
181
326