113
Appendix
Notes and Cautions
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and
operating instructions should
be read before the appliance is
operated.
• Retain Instructions: The safety and
operating instructions should be
retained for future reference.
• Heed Warnings: All warnings on the
appliance and in the operating
instructions should be adhered to.
• Follow Instructions: All operating
and use instructions should be
followed.
Installation
Installation
Power Sources: This video product
should be operated only from the
type of power source indicated on
the marking label. If you are not sure
of the type of power supply to your
home, consult your appliance dealer
or local power company. For video
products intended to operate from
battery power, or other sources,
refer to the operating instructions.
Grounding or Polarization: This
video product is equipped with a
polarized alternating-current line
plug (a plug having one blade
wider than the other). This plug will
fit into the power outlet only one
way. This is a safety feature. If you
are unable to insert the plug fully
into the outlet, try reversing the
plug. If the plug should still fail to fit,
contact your electrician to replace
your obsolete outlet. Do not defeat
the safety purpose of the polarized
plug.
Alternate Warnings: This video
product is equipped with a 3-wire
grounding-type plug, a plug having
a third (grounding) pin. This plug
will only fit into a grounding-type
power outlet. This is a safety feature.
If you are unable to insert the
plug into the outlet, contact your
electrician to replace your obsolete
outlet. Do not defeat the safety
purpose of the grounding-type
plug.
Overloading: Do not overload wall
outlets and extension cords as this
can result in a risk of fire or electric
shock.
Ventilation: Slots and openings
in the cabinet are provided for
ventilation and to ensure reliable
operation of the video product
and to protect it from overheating,
and these openings must not be
blocked or covered.
The openings should never be
blocked by placing the video
product on a bed, sofa, rug, or other
similar surface.
This video product should not
be placed in a built-in installation
such as a bookcase or rack unless
proper ventilation is provided or the
manufacturer’s instructions have
been adhered to.
This video product should never
be placed near or over a radiator or
heat register.
Attachments: Do not use
attachments not recommended by
the video product manufacturer as
they may cause hazards.
Water and Moisture: Do not use this
video product near water – for
example, near a bath tub, wash
bowl, kitchen sink, or laundry
tub, in a wet basement, or near a
swimming pool, and the like.
Power-Cord Protection: Power-Supply
cords should be routed so that
they are not likely to be walked
on or pinched by items placed
upon or against them, paying
particular attention to cords at
plugs, convenience receptacles, and
the point where they exit from the
appliance.
Accessories: Do not place this video
product on an unstable cart, stand,
tripod, bracket, or table. The video
product may fall, causing serious
injury to a child or adult, and
serious damage to the appliance.
Use only with a cart, stand, tripod,
bracket, or table recommended
by the manufacturer, or sold with
the video product. Any mounting
of the appliance should follow the
manufacturer’s instructions, and
should use a mounting accessory
recommended by the manufacturer.
An appliance and
cart combination
should be moved
with care. Quick
stops, excessive
force, and uneven
surfaces may
cause the appliance and cart
combination to overturn.
Antennas
Antennas
Outdoor Antenna Grounding: If an
outside antenna or cable system is
connected to the video product,
be sure the antenna or cable
system is grounded so as to
provide some protection against
voltage surges and built-up
static charges. Section 810 of the
National Electrical Code, ANSI/NFPA
No. 70, provides information with
respect to proper grounding of
the mast and supporting structure,
grounding of the lead-in wire to
an antennadischarge unit, size of
grounding conductors, location of
antenna-discharge unit, connection
to grounding electrodes, and
requirements for the grounding
electrode.