Filter
Top Products
EN63
1
2
3
4
5
6
7
8
––:–– ~
~
~
~
~
~
~
~
–
–
:
––
0
:
000
––
TOTAL
CODETIME
NIOUT
MODE
PLAY
R.A.EDIT
ON/OFF
EFFECT
FADE/WIPE
EDIT IN/OUT
CANCEL
REW
FF
ON/OFF
IN/OUT
SELECT SCENES
4
Point the remote control at the camcorder’s remote
sensor. Press PLAY (
4
) and then press R.A.EDIT ON/
OFF or ON/OFF on the remote control.
The Random Assemble Editing Menu appears.
5
For GR-DVL915/DVL815 Owners:
If using a Fade/
Wipe at the beginning of the scene, press FADE/WIPE
on the remote control.
•Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
•You cannot use a Picture Wipe/Dissolve at the
beginning of Program 1.
6
At the beginning of the scene, press EDIT IN/OUT or
IN/OUT on the remote control. The Edit-In position
appears in the Random Assemble Editing Menu.
7
At the end of the scene, press EDIT IN/OUT or IN/
OUT. The Edit-Out position appears in the Random
Assemble Editing Menu.
8
For GR-DVL915/DVL815 Owners:
If using a Fade/
Wipe at the end of the scene, press FADE/WIPE.
•Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
•If you select a Fade/Wipe effect for an Edit-Out
point, the effect is automatically applied to the
following Edit-In point.
•You cannot use a Picture Wipe/Dissolve at the end
of the last scene.
•When you use Fade/Wipe effects, that time is
included in the total time (this does not apply to
Picture Wipe/Dissolve).
1
9
For GR-DVL915/DVL815 Owners:
If using Playback
Special Effects, press EFFECT (੬ pg. 59).
10
Repeat steps 6 through 9 to register additional scenes.
•To change previously registered points, press
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
•
For GR-DVL915/DVL815 Owners:
If you are not
using Fade/Wipe or Program AE with special effects,
repeat steps 6 and 7 only.
NOTES:
●
When choosing a scene, set Edit-In and Edit-Out points so that there is a relatively large difference between
them.
●
If the search time for an in-point exceeds 5 minutes, the recording deck’s Record-Standby mode will be
canceled and editing will not take place.
●
If there are blank portions before or after the Edit-In and Edit-Out points, a blue screen may be included in
the edited version.
●
Since time codes register time only as accurately as seconds, the time code total time may not match the
total program time exactly.
●
Turning off the camcorder’s power erases all registered Edit-In and Edit-Out points.
For GR-DVL915/DVL815 Owners:
●
If you select Sepia or Monotone mode from Program AE with special effects, you cannot use the Dissolve or
Black & White Fader. In this case the Dissolve or Black & White indicator begins blinking. Once the next
Edit-In point is registered, the effect is turned off. To combine these effects, use Sepia or Monotone during
recording, then use the Dissolve or Black & White Fader during Random Assemble Editing.
●
It is not possible to use Fade/Wipe effects and Program AE with special effects during Random Assemble
Editing using a DV cable.
Random Assemble
Editing Menu
Program
Remote sensor
RM-V716U
(Provided with
GR-DVL915/
DVL815 only)
RM-V700U
(optional)
OR
CONTINUED ON NEXT PAGE