Panasonic WV-SW396E Security Camera User Manual


  Open as PDF
of 40
 
• 24 V AC power supply connector kit (accessory)
Recommended specification of cable (wire)
Wire size
(AWG),
stranded
wire
#24
(0.22 mm)
#22
(0.33 mm)
#20
(0.52 mm)
#18
(0.83 mm)
Length of
cable
20 m
{65.62 feet}
30 m
{98.43 feet}
45 m
{147.64 feet}
75 m
{246.06 feet}
Terminals of the power supply connector
Pin No. Signal
1
2
3
4
24 V AC LIVE
24 V AC NEUTRAL
Ground
Not use
• How to assemble the power supply connector
Remove approx. 3 mm {1/8 inches} of the outer jacket of
the cable and twist the cable core to prevent the short cir-
cuit first.
Insert the tip of the cable into the point A of the contact,
and hold the cable using the cable clamp.
Procure either of the following tools for clamping.
Molex manual clamp tool:
57027-5000 (for UL1015), 57026-5000 (for UL1007)
After clamping the contact and the cable, insert the con-
tact properly into the power supply connector housing.
Important:
 • Conduct the electric conduit work after processing
the power supply connector and making sure that the
camera is operating normally.
• Network cable
Connect a LAN cable (category 5e or better, STP*) to the
network connector.
* E model only
Important:
 • Useall4pairs(8pins)oftheLANcable.
 • Themaximumcablelengthis100m{328feet}.
 • MakesurethatthePoE+deviceinuseiscompliant
with IEEE802.3at standard.
 • Whenconnectingbothofthe24VACpowersupply
and the PoE+ device for power supply, 24 V AC will
be used for power supply.
Depending on PoE+ (or PoE) devices, the power sup-
ply indicator may light or the network functions may
be unavailable.
In this case, disable the PoE+ (or PoE) settings. Refer
to the operating instructions of the PoE+ (or PoE)
device in use.
• Output cable for the monitor used for adjustment
Connect a coaxial cable (BNC) (only for checking if images
are displayed on the monitor).
This output is provided only for checking the adjustment
of the angular field of view on the video monitor when
installing the camera or when servicing.
Important:
 • Themonitoroutconnectorforadjustmentisprovided
only for checking the adjustment of the angular field
of view on the video monitor when installing the cam-
era or when servicing. It is not provided for recording/
monitoring use.
 • Blackbands mayappear atthe topandbottom or
right and left of the screen. (That does not affect the
adjustment because the angular field of view is not
changed.)
• External I/O cable
Important:
 • InputandoutputoftheexternalI/Oterminal2and3
can be switched by configuring the setting. The
default of EXT I/O terminal 2 is "ALARM IN 2" and of
EXT I/O terminal 3 is "ALARM IN 3". It is possible to
determine whether or not to receive input from EXT
I/O terminal 2 and 3 (ALARM IN2, 3) by selecting
"Off", "Alarm input", "Alarm output" or "AUX output"
for "Terminal alarm 2" or "Terminal alarm 3" on the
[Alarm] tab on the "Alarm" page. Refer to the
Operating Instructions (included in the CD-ROM) for
further information.
 • WhenusingtheEXTI/Oterminalsastheoutputtermi-
nals, ensure they do not cause signal collision with
external signals.
Contact
Insert
Upper
side
A
Approx. 3 mm {1/8 inches}
Cable
1
3
2
4
Contact
Power supply connector housing (accessory)
Upper side
Cable
23
 previous next