Filter
Top Products
SHORT COURSES (HTTP://WWW.SHORTCOURSES.COM)
25
Omni Selector to scroll through the images. Press the up
point to increase or decrease the number of copies for the
current image. (The default is 0.) The number of copies of
that image, and the running total of all images are dis-
played at the top of the monitor. When finished, press
MENU.
■ To select all images for printing, highlight Order and
press SET. Then press the Flash/Index button, then SET
again to display a menu. Highlight Mark All and press SET.
You can scroll through the images to change quantities with
the up or down point on the Omni Selector. The number of
copies of that image, and the running total of all images are
displayed at the top of the monitor. When finished, press
MENU.
■ To specify the print type, highlight Set up and press SET.
Highlight Print type and press the left or right point on the
Omni Selector to select Standard, Index, or Both and press
SET again. (You can also specify if the date and file number
is printed on the image by turning those features on.) When
finished, press MENU.
■ To clear all previously entered print order settings,
highlight Reset and press SET. Highlight OK and press SET.
4. Press the MENU button to hide the menu.
ADJUSTING CONTRAST, SHARPNESS, AND SATURATION
1. With the camera on and the Mode Dial set to any mode in
Creative Zone mode, press MENU.
2. Press the down point on the Omni Selector to highlight
Contrast, Sharpness, or Saturation (you have to scroll down
to see them).
3. Press the left point on the Omni Selector to decrease the
setting (–), or the right point to increase it (+).
4. Press MENU to confirm the setting and hide the menu.
5. When finished, repeat Steps 1–4 to reset controls to 0 or
they will be remembered even when you turn the camera
off and back on.
USING THE SET UP MENU
1. With the Mode Dial set to any mode, press the MENU
© COPYRIGHT 2001 BY DENNIS P. CURTIN
26
button to display the menu. Notice how one of the menu’s
tabs is highlighted and an arrowhead points toward the
next tab. (If a tab isn’t highlighted, press the up point on
the Omni Selector until it is.)
2. Press the right or left point on the Omni Selector to high-
light the Set Up menu tab. (You can also press JUMP
without needing to highlight the tab.)
3. To change an item on the menu, press the points on the
Omni Selector to do any of the following and then press
SET:
■ To turn the beep on and off, highlight Beep, and then
select On or Off.
■ To change the brightness of the monitor highlight LCD
Brightness, and then select the dim or bright icon.
■ To change the volume, highlight Playback Vol (in Replay
mode) or Shutter Volume (in shooting mode) and increase or
decrease the volume.
■ To turn power down mode on or off, highlight Auto
Power Down and select On or Off.
■ To set the date and time, highlight Date/Time, and then
press the right point on the Omni Selector to display the Set
Date/Time Screen. Press the left or right point to select an
element and the up or down point to change it. When
finished, press SET. (In Replay mode, hold down SET and
press JUMP to go directly to this setting.)
■ To format a flash memory card, highlight Format, and
then press the right point on the Omni Selector to display a
confirmation screen. Press the left or right point to select
Cancel or OK and press SET. BE CAREFUL with this
command because it will erase your image files.
■ To specify a language for the menus, highlight Lan-
guage, and then press the right point on Omni Selector to
display a list of languages. Press the up or down point to
select a language and press SET.
■ To specify the video system, highlight Video System and
press the right or left point on the Omni Selector to select
NTSC or PAL.
4. When finished making changes, press the MENU button to
hide the menu.