Filter
Top Products
38
Ⅵ Allowed characters
Pressing the SELECTOR button in the t direction will select the
character on the right and pressing in the 8 direction will select the
character on the left. Pressing and holding the button will continu-
ously change the character selected.
Memo
When CAMERA TITLE is set to ON, a background the width of 1
character is displayed, even when there is no camera title entered.
If a CAMERA TITLE of more than 1 character is entered, a back-
ground the width of 24 characters is displayed.
8 direction (SELECTOR button) t direction
Space
39
MENU SETTING
FACTORY SETTINGS screen
Returns set values to their factory settings.
1.
Display the FACTORY SET-
TINGS screen. (੬ Page 24)
2.
Press the SELECTOR button in
the vertical direction (6 or 7)
and move the cursor (>) to
CLEAR.
3.
Press the SET button.
● Settings including the camera
title will be restored to the fac-
tory settings and the screen
will return to the MENU screen.
* Select CANCEL and press the
SET button to return to the
MENU screen without chang-
ing settings.
4.
Exit the menu screen.
Select EXIT within the MENU
screen and press the SET but-
ton to return to the normal screen.
VIDEO ADJUST..
FOCUS ADJUST..
CAMERA SETT NGSI..
FACTORY SETT NGSI..
MENU
CANC
F— — — — — —
— — — — — —
ACTORY S
E
TTINGS
EL
CLEA
EXIT
R
Cursor
Operation
40
Troubleshooting
OTHERS
Symptom Remedy
The operation becomes un-
stable
The auto iris will not operate
There is noise in the screen
or increase in residual im-
ages
The colors of the screen are
not natural
White balance adjusted
automatically/manually
cannot be used
The camera title will not ap-
pear
The vertical phase cannot be
adjusted using the V PHASE
menu item
Drop in voltage of the power supply can
be considered. Check the length and
thickness of the power supply cable.
(੬ Page 17)
Set the VIDEO/DC switch on the side
of unit according to the type of auto iris
lens used.
(੬ Pages 20, 21)
Lower the gain using the AGC MODE
menu item.
ULTRA SUPER HIGH MID LOW OFF
(MAX) (MIN)
Gain
(੬ Page 31)
When using in an environment where
there are changes in the light source,
set the WHITE BALANCE menu item
to ATW.
(੬ Page 33)
Set the WHITE BALANCE menu item
to AWB or MANUAL.
(੬ Page 33)
Set the CAMERA TITLE menu item to
ON.
(੬ Page 36)
When adjusting the vertical phase dur-
ing line lock, set the LL/INT switch on
the back of unit to LL.
(੬ Page 11)
41
OTHERS
Specifications
Image pickup device : 1/3 type WDR digital image device
Number of effective pixeis : 380,000 pixels ((H) 720 × (V) 540)
Synchronizaton method : Internal,Line lock
Scanning frequency :
U Type (H) 15.734 kHz, (V) 59.94 Hz
E type (H) 15.625 kHz, (V) 50.0 Hz
Resolution : 480 TV lines (H)
VIDEO OUT : Composite video signal
1 V(p-p), 75Ω (BNC)
Video S/N ratio : 50 dB (AGC OFF)
Minimum required illumination
: 1.9 lx (50%, F1.2, AGC HIGH)
0.5 lx (50%, F1.2, AGC ULTRA(×16))
0.95 lx (25%, F1.2, AGC HIGH)
0.25 lx (25%, F1.2, AGC ULTRA(×16))
Lens mount : CS mount
Power supply : AC 24 V ` 50 Hz/60 Hz
DC 12 V
Power consumption : U type Approx. 5.7 W
E type Approx. 400 mA
Ambient temperature : –10°C to 50°C (operation)
0°C to 35°C (recommended)
Mass : 330 g
Accessory : Instructions
U type ..............................1
E type ..............................2
Ferrite core .......................1
Ⅵ External Dimensions (Unit: mm)
Design and specifications are subject to change without notice.
COLOR VIDEO CAMERA
1/4-20UNC
MOUNTING HOLE
U1-32
50
57.5
7.5
50
107
95
33
TRIPOD
BASE