Filter
Top Products
107
Saving and Loading Scene Files
Chapter 6 Saving and Loading User Setting Data
3
Load a scene file.
To load a scene file stored in the camcorder
Turn the MENU knob to move the
b mark to the
desired file number, and press the MENU knob.
The s which is displayed on the left of the file number
changes to x.
The camcorder is set up according to the loaded scene
file.
To cancel the selected scene file
Move the
b mark to x, and press the MENU knob. x
changes to s.
The camcorder returns to the settings before selecting
this scene file.
To load a scene file saved in the “Memory Stick”
Proceed as follows:
1 Turn the MENU knob to move the
b mark to
“SCENE RECALL,” and press the MENU knob.
The P00 SCENE RECALL page appears.
2 Turn the MENU knob until the page which
contains the desired file number appears, then press
the MENU knob.
3 Turn the MENU knob to move the
b mark to the
desired file number, and press the MENU knob.
The message “RECALL OK? YES bNO” appears.
4
To carry out the recall, move the b mark to “YES” and
press the MENU knob.
To cancel, press the MENU knob leaving the
b mark
pointing to “NO.”
When the loading is completed, the message
“COMPLETE” appears. The camcorder is set up
according to the loaded scene file.
If no file is present with a particular file number, this is
shown as “NO FILE.”
5
To end the menu operation, set the MENU ON/OFF
switch to OFF.
Loading scene files from a “Memory Stick”
into the camcorder memory
You can load up to five scene files stored in the “Memory
Stick” into the camcorder memory in a single operation.
1
After displaying the SCENE FILE page (page 104),
turn the MENU knob to move the
b mark to “SCENE
RECALL,” and press the MENU knob.
A SCENE RECALL page appears.
2
Turn the MENU knob until the SCENE RECALL page
which contains the desired scene files appears, then
press the MENU knob.
3
Turn the MENU knob to move the b mark to “5FILE
LOAD
b MEM 1-5,” and press the MENU knob.
The message “RECALL OK? YES bNO” appears.
4
To carry out the recall, move the b mark to “YES” and
press the MENU knob.
To cancel, press the MENU knob leaving the
b mark
pointing to “NO.”
When loading is complete, the message
“COMPLETE” appears and the ACCESS indicator
goes off.
5
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
• The scene files loaded from the “Memory Stick”
overwrite data saved in the camcorder memory.
F04 SCENE FILE
s
1 :SCENE 25
x
2 :SCENE 26
s
3 :SCENE 27
s
4 :SCENE 28
s
5 :NO FILE
s
STANDARD
SCENE RECALL : EXEC
SCENE STORE : EXEC
F.ID: SCENE21
TOP
?P00 SCENE RECALL
DISPLAY MODE : F.ID
MEM<1>:STANDARD
MEM<2>:STANDARD
MEM<3>:STANDARD
MEM<4>:STANDARD
MEM<5>:NO FILE
ESC
P01 SCENE RECALL
RECALL OK? YES NO
DISPLAY MODE : ALL
001.SCENE1
002.SCENE2
003.NO FILE
004.SCENE4
005.SCENE5
***.5FILE LOAD MEM1-5
ESC
Notes
P01 SCENE RECALL
RECALL OK? YES NO
DISPLAY MODE : ALL
001.SCENE1
002.SCENE2
003.NO FILE
004.SCENE4
005.SCENE5
***.5FILE LOAD MEM1-5
ESC