Filter
Top Products
28
Command List
EVI-HD1 Command List (3/3)
Command Set Command Command Packet Comments
CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs: Camera ID (=0000 to FFFF)
IR_Receive On 8x 01 06 08 02 FF IR(remote commander) receive ON/OFF
Off 8x 01 06 08 03 FF
On/Off 8x 01 06 08 10 FF
IR_ReceiveReturn On 8x 01 7D 01 03 00 00 FF IR (remote commander) receive message via the VISCA
communication ON/OFF
Off 8x 01 7D 01 13 00 00 FF For contents of messages, see page 30.
D-SUB 15Pin SYNC 3-STATE 8x 01 7E 01 1A 00 00 FF Setting the sync of the HD analog component output
VD 8x 01 7E 01 1A 00 01 FF
Information Display On 8x 01 7E 01 18 02 FF ON/OFF of the Operation status display of One Push
Off 8x 01 7E 01 18 03 FF Trigger of CAM_Memory and CAM_WB
Pan-tiltDrive Up
3)
8x 01 06 01 VV WW 03 01 FF VV: Pan speed 0 x01 (low speed) to 0 x18 (high speed)
Down
3)
8x 01 06 01 VV WW 03 02 FF WW: Tilt Speed 0 x 01 (low speed) to 0 x14 (high speed)
Left
3)
8x 01 06 01 VV WW 01 03 FF YYYY: Pan Position FA60 to 05A0 (center 0000)
Right
3)
8x 01 06 01 VV WW 02 03 FF ZZZZ: Tilt Position FE98 to 0168 (center 0000)
UpLeft
3)
8x 01 06 01 VV WW 01 01 FF
UpRight
3)
8x 01 06 01 VV WW 02 01 FF See page 37.
DownLeft
3)
8x 01 06 01 VV WW 01 02 FF
DownRight
3)
8x 01 06 01 VV WW 02 02 FF
Stop
3)
8x 01 06 01 VV WW 03 03 FF
AbsolutePosition 8x 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
RelativePosition 8x 01 06 03 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
Home 8x 01 06 04 FF
Reset 8x 01 06 05 FF
Pan-tiltLimitSet LimitSet 8x 01 06 07 00 0W W: 1 UpRight 0: DownLeft
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF YYYY: Pan Limit Position FA60 to 05A0 (center 0000)
LimitClear 8x 01 06 07 01 0W ZZZZ: Tilt Position FE98~0168 (center 0000)
07 0F 0F 0F 07 0F 0F 0F FF
1)After an ACK to a One Push White Balance Trigger is sent until the operation is completed, “Not Executable” is sent as a reply when any
other commands are received.
When a slow shutter speed (1/20, 1/25 or lower) is selected, the time needed for the One Push White Balance adjustment will be longer.
2)Bright can be set only in Full Auto mode or Shutter Priority mode.
3)When the menu is displayed, this operation is ignored.
4) When other commands are received after a Completion notification for the Recall command is sent, “Command not executable” may be
returned for a maximum of 240 msec due to internal processing. In this case, please transmit the command again.