Filter
Top Products
EN
30
USING MENUS FOR DETAILED ADJUSTMENT
MELODY
EEPB
–
RETURN
AM RESETC
LCD
RIORITYP
–
ON
EMO MODED
–
ON
EMOTER
–
ON
ALLYT
–
SYSTE
M
RETURN
–
–
–
AREMACD
ISPLAY
RE NEON SC
LCD/ TV
UAOT
IMETDATE /
T I ME CODE
CLOCK
ADJ .
FFO
25 ’03
CED
30
PM
:5
BR IGHT
SYSTEM
“ SYSTEM” functions which are set when the Power
Switch u is set to “ ” are also applied when the
Power Switch u is set to “PLAY” (੬ pg. 31).
BEEP
OFF: Even though not heard while shooting, shutter
sound is recorded on the tape.
BEEP: The beep sounds when the power is turned on
or off, and at the beginning and end of recording. Also
to activate the shutter sound effect (੬ pg. 17, 25).
[MELODY]: Instead of a beep, a melody sounds
when any operation is performed. It also activates the
shutter sound effect (੬ pg. 17, 25).
TALLY
OFF: The tally lamp remains off at all times.
[ON]: The tally lamp comes on to signal the start of
recording.
REMOTE
OFF: Disables the camcorder from receiving the
remote control's beam signals. The camcorder cannot
be operated by the remote control.
[ON]: Enables the camcorder to receive the remote
control’s beam signals.
DEMO MODE
OFF: Automatic demonstration will not take place.
[ON]: Demonstrates certain functions such as
Program AE with special effects, etc., and can be
used to confirm how these functions operate.
Demonstration starts in the following cases:
• When the Menu Screen is closed after “DEMO
MODE” is turned “ON”.
• With “DEMO MODE” set to “ON”, if there is no
operation for about 3 minutes after the Power
Switch u is set to “ ” or “ ” .
Performing any operation during the demonstration
stops the demonstration temporarily. If no operation is
performed for more than 3 minutes after that, the
demonstration will resume.
NOTES:
● If a tape is in the camcorder, the demonstration cannot be
turned on.
● “DEMO MODE” remains “ON” even if the camcorder
power is turned off.
● If “DEMO MODE” remains “ON”, some functions will not
be available. After viewing demo, set to “OFF”.
PRIORITY
[LCD]: When the LCD monitor is fully open, even if
the viewfinder is pulled out, the image is displayed
only on the LCD monitor; it will not be displayed in the
viewfinder.
FINDER: When the viewfinder is pulled out, even if
the LCD monitor is fully open, the image is displayed
only in the viewfinder; it will not be displayed on the
LCD monitor.
CAM RESET
[CANCEL]: Does not reset all settings to the
factory-preset.
EXECUTE: Resets all settings to the factory-preset.
CAMERA DISPLAY
• Settings made in the “ CAMERA DISPLAY” Menu
are effective only for video shooting.
• Settings made in the “ CAMERA DISPLAY” Menu
remain effective even when the Power Switch u is set
to “ ”. However, the menu settings can be changed
only when the Power Switch u is set to “ ”.
BRIGHT
੬ pg. 12, “To Adjust The Brightness Of The Display”
ON SCREEN
LCD: Keeps the camcorder’s display (except the date,
time and time code) from appearing on the connected
TV screen.
[LCD/TV]: Makes the camcorder’s display appear on
screen when the camcorder is connected to a TV.
DATE/TIME
OFF: The date/time does not appear.
[AUTO]: Displays the date/time for approx. 5
seconds in the following cases:
• When the Power Switch u is set from “OFF
(CHARGE)” to “ ” or “ ”.
• When tape playback starts. The camcorder displays
the date/time when scenes are recorded.
• When the date is changed during tape playback.
ON: The date/time is always displayed.
• The date indication can also be turned on/off by
pressing the DISPLAY Button U on the remote
control.
[ ] = Factory-preset
1 GR-D91US EN 23-34 02.11.6, 2:15 PM30