Filter
Top Products
EN
31
USING MENUS FOR DETAILED ADJUSTMENT
TIME CODE
[OFF]: Time code is not displayed.
ON: Time code is displayed on the camcorder and on
the connected TV. Frame numbers are not displayed
during recording.
CLOCK ADJ.
Allows you to set the current date and time (੬ pg. 10).
DSC
QUALITY , IMAGE SIZE
Refer to “Picture Quality/Image Size Setting”
(੬ pg. 11).
REC SELECT
[ ]: When Snapshot recording is performed
with the VIDEO/DSC Switch 4 set to “VIDEO”, still
images are recorded only onto the tape.
/ : When Snapshot recording is
performed with the VIDEO/DSC Switch 4 set to
“VIDEO”, still images are recorded not only onto the
tape but also on the memory card (640 x 480 pixels).
In this mode, the “SNAP MODE” selection in the
CAMERA Menu is also applicable to memory card
recording.
VIDEO
SOUND MODE
........੬ pg. 32, “Playback Sound”.
12BIT MODE
........੬ pg. 32, “Display”.
SYNCHRO
........੬ pg. 38, “For More
Accurate Editing”.
REC MODE
Allows you to set the tape recording mode ([SP] or
LP) depending on your preference (੬ pg. 10).
It is recommended you use “REC MODE” in the
“ VIDEO” Menu when using this camcorder as a
recorder during dubbing (੬ pg. 33, 34).
•“REC MODE” can be set when the Power Switch u is
set to “PLAY” or “ ” (੬ pg. 10, 28).
COPY
ON: Enables dubbing of images recorded on a tape
to a memory card (੬ pg. 21).
[OFF]: Enables snapshots to be taken during tape
playback.
S/AV INPUT
ON: Enables audio/video signal input from the AV
and S-VIDEO connectors (੬ pg. 33).
[OFF]: Enables audio/video signal output to a TV,
VCR, etc. via the AV and S-VIDEO connectors (੬
pg. 16, 33).
• When “S/AV INPUT” is set to “ON”, camcorder
playback cannot be viewed on the AV output.
–
RETURN
–
–
DSC
TYQUAL I
REC SELECT
FINE
021X7486
IMAGE SIZE
–
–
–
–
–
–
IVDE
O
MDOESOUND
MDOE
12
BIT
ROSYNCH
ODEREC M
COPY
STEREO
SOUND
1
OFF
OFF
O.O
NPUT
S/
AV I
RETURN
MELODY
EEPB
–
RETURN
AM RESETC
LCD
RIORITYP
–
ON
EMO MODED
–
ON
EMOTER
–
ON
ALLYT
–
SYSTE
M
For Playback Menu
The following procedure applies to all except Synchro
Comp (੬ pg. 38).
1 Set the VIDEO/DSC Switch 4 to “VIDEO”, then set
the Power Switch u to “PLAY” while pressing down the
Lock Button y located on the switch.
2 Press the MENU/VOLUME wheel % in. The Menu
Screen appears.
3 Rotate the MENU/VOLUME wheel % to select the
desired function menu, and press it.
4 Rotate the MENU/VOLUME wheel % to select the
desired function, and press it to display the Sub Menu.
5 Rotate the MENU/VOLUME wheel % to select the
desired parameter and press it. Selection is complete.
6 Rotate the MENU/VOLUME wheel % to select
“ RETURN” and press it twice to close the Menu
Screen.
SYSTEM
Each setting is linked with “ SYSTEM”, which
appears when the Power Switch u is set to “ ”
(੬ pg. 30).
The parameters are the same as in the description on
pg. 30.
[ ] = Factory-preset
1 GR-D91US EN 23-34 02.11.6, 2:15 PM31