Filter
Top Products
78
Adjustments and Settings for Recording
: Viewfinder Screen Status Displays
Information Item Indication Status
11. Camera Warning
and Report Area
AWB A ACTIVE
AWB B ACTIVE
AWB A OK .K
AWB B OK .K
AWB BREAK .K
AWB NG
COLOR TEMP LOW
COLOR TEMP HIGH
LEVEL OVER
LOW LIGHT
TIME OVER
AWB PRESET .K
CHECK FILTER
ABB ACTIVE
ABB OK
ABB BREAK
ABB NG
B-SHD READY
B-SHD ACTIVE
B-SHD OK
B-SHD BREAK
B-SHD NG
AWB being performed on Ch A.
AWB being performed on Ch B.
AWB successful on Ch A.
AWB successful on Ch B.
AWB action aborted by user.
AWB action failed. The second line indicates the status.
Color temperature too low.
Color temperature too high.
Brightness too high.
Brightness too low.
Action timed-out.
AWB cannot be performed because the AWB switch is position at [PRST] or
the super gain is enabled.
Make sure the FILTER control is positioned correctly.
ABB being performed.
ABB action successful.
ABB action aborted by user.
ABB action failed.
Black shading accepted (by holding down the ABB switch during ABB
adjustment).
Black shading being adjusted.
Black shading adjustment successful.
Black shading adjustment aborted by user.
Black shading adjustment failed.
(Related to AWB, ABB
and switch settings)
(Switch changeover
indication)
WHITE: # .K
AUTO KNEE: ON/OFF
GAIN: dB
SS: 1/, .d,
X.d
SS: X 1/, XX1/
ND: /CC: K
EXTENDER: ON/OFF/K
IRIS: F .
DRS: ON/OFF
The WHITE BAL switch has been switched. # is replaced with A, B or PRE.
AUTO KNEE switch has been switched to [ON] or [OFF].
Gain has been switched with the GAIN selector switch or a user button.
When the shutter speed has been switched, the shutter speed is indicated.
Shutter speed is in SYNCHRO SCAN mode.
This appears when the filter setting has been selected.
Lens extender has been turned on or off.
Indicated when the iris override correction value is to be changed.
The dynamic range stretcher has been switched.
(Low light warning) LOW LIGHT Brightness too low.
(Y GET value) .% With the Y GET ON setting, the output brightness level near the center marker
is displayed as “%”.
12. User button
functions
INH
I.OVR ON/OFF
S.BLK –/OFF
B.GAMMA ON/OFF
Y GET ON/OFF
DRS ON/OFF
ASSIST ON/OFF
C.TEMP ON/OFF
VFR ON/OFF
FRATE ON/OFF
VF GAM ON/OFF
AUDIO CH1
AUDIO CH2
REC SW
RET SW
PRE REC
SLOT SEL
USB HOST/DEVICE/OFF
VF MARK A/B/OFF
TEXT MEMO
User buttons disabled.
Iris override can be set (the iris override setting is on).
Status of super black (on or off). When it is on, the set value is also indicated.
Status of black gamma (shade correction for the black level): on or off
Indicates whether the Y GET function is on or off.
Indicates whether the dynamic range stretcher function is on or off.
Indicates whether the focus assist function is on or off.
Indicates the mode for changing the color temperature with the jog dial button
is on or off.
Indicates whether the VFR function is on or off.
Indicates whether the frame rate set in USR SW F.RATE is being applied.
Indicates whether the monitor gamma function is enabled for the viewfinder.
Input signal to be recorded on audio channel 1 has been switched.
Input signal to be recorded on audio channel 2 has been switched.
User button acts as REC switch.
User button acts as RET switch.
Indicates that PRE RECORDING mode has been switched on or off.
Switch that changes the target card is set.
USB action status has been switched.
Displayed when the marker displayed in the viewfinder and on the LCD screen
has been changed.
Indicates whether the TEXT MEMO function is on or off.
UM:
U1:
U2:
U3:
U4:
USER MAIN
button
USER 1 button
USER 2 button
MARKER
SELECT button
TEXT MEMO
button
AJ-HPX2700G-VQT1V27_eng.book 78 ページ ２００８年９月２日 火曜日 午後５時４３分