Filter
Top Products
88
Adjustments and Settings from Menus
Chapter 5 Menu Displays and Detailed Settings
ASSIGN <2> SEL window
TURBO SW SEL window
1) This does not appear if the CBK-MB01 is not installed.
2)Even when the MARKER item is set to “OFF” on the MARKER
page of the USER menu, the ASSIGN 1 switch (or TURBO GAIN
button) allows you to display or not to display all markers.
3)Even if the RETURN VIDEO item is set to “OFF” on the GENLOCK
page of the MAINTENANCE menu, you can use this switch to
display the image of the return video signal on the viewfinder.
4) This does not appear if nothing is assigned in the Assign menu.
1) This does not appear if the CBK-MB01 is not installed.
2) Even when the MARKER item is set to “OFF” on the MARKER
page of the USER menu, the ASSIGN 2 switch allows you to display
or not to display all markers.
3) This does not appear if nothing is assigned in the Assign menu.
For functions that are assigned to the ASSIGN 2
(slide-type) switch, you cannot change those settings
using other menus. The function assigned to ASSIGN
2 switch takes precedence over the menu setting.
4
Turn the MENU knob to move the b mark to the item
you want to set, and press MENU knob.
The
b mark changes to a z mark, and the z mark by
the setting changes to a ? mark.
5
Turn the MENU knob to switch to the desired setting,
and press the MENU knob.
The z mark returns to a
b mark, and the ? mark
returns to a z mark, confirming the setting.
6
To continue with other settings, repeat steps 3 and 4.
To return to the previous page
Turn the MENU knob to move the
b mark to “ESC” at the
right top of the window and press the MENU knob.
Alternatively, push the CANCEL/PRST / ESCAPE switch
down to the ESCAPE side.
To end the menu operation
Set the MENU ON/OFF switch to OFF or close the cover
of the menu operating section.
Functions to be assigned to the ASSIGN 1 (push-type)
switch and TURBO GAIN button
Function Description
OFF Disables the switch.
PICTURE
CACHE
ON/OFF
1)
Assigns Picture Cache mode ON/OFF
function.
TEST OUT
CHARACTER
Assigns the function to switch whether
or not text is superimposed on the
video signal to be output from the TEST
OUT connector.
MARKER Assigns the ON/OFF function to display
all markers.
2)
RE-TAKE Assigns the RE-TAKE function.
ATW Assigns the ON/OFF function of auto-
tracing white balance.
RETURN
VIDEO
Assigns the ON/OFF function to display
the image of the return video signal on
the viewfinder.
3)
LENS RET Assigns the same function as that of
the RET switch on the lens.
REC SWITCH Assigns the VTR S/S (start/stop)
function.
TURBO
SWITCH
Assigns the TURBO GAIN function.
ZEBRA Assigns the zebra pattern display
function.
D5600 Applies an electrical 5600K filter.
UA01 to
UA10
4)
Assigns the items assigned in the
ASSIGN SEL menu.
ASSIGN <2> SEL ESC
OFF
PICTURE CACHE ON/OFF
TEST OUT CHARACTER
MARKER
ZEBRA
D5600
EXT REC CONTROL
TURBO SW SEL ESC
OFF
PICTURE CACHE ON/OFF
TEST OUT CHARACTER
MARKER
RE-TAKE
ATW
RETURN VIDEO
LENS RET
REC SWITCH
TURBO SWITCH
Functions to be assigned to
the ASSIGN 2 (slide-type) switch
Function Content
OFF Disables the switch.
PICTURE
CACHE
ON/OFF
1)
Assigns Picture Cache mode ON/OFF
function.
TEST OUT
CHARACTER
Assigns the function to switch whether
or not the characters are mixed to the
video signal to be output from the TEST
OUT connector.
MARKER Assigns the ON/OFF function to display
all markers.
2)
ZEBRA Assigns the zebra pattern display
function.
D5600 Applies an electrical 5600K filter.
EXT REC
CONTROL
Selects whether or not recording
control of external devices connected
through the CCZ connector (26-pin) of
a CA-702 is possible.
UA01 to
UA10
3)
Assigns the items assigned in the
ASSIGN SEL menu.
Note