Filter
Top Products
EDITING
46 EN
MasterPage: Left
Select Scenes
6 Press PLAY (U) and then press R.A.EDIT ON/OFF on
the remote control.
● The Random Assemble Editing
Menu appears.
7 If using a Wipe/Fader at the
beginning of the scene, press
FADE/WIPE on the remote
control.
● Cycle through the effects by
pressing repeatedly, and stop
when the one you want is
displayed.
8 At the beginning of the scene, press EDIT IN/OUT on
the remote control. The Edit-In position appears in the
Random Assemble Editing Menu.
9 At the end of the scene, press EDIT IN/OUT. The Edit-
Out position appears in the Random Assemble Editing
Menu.
10 If using a Wipe/Fader at the end of the scene, press
FADE/WIPE.
● Cycle through the effects by pressing repeatedly, and stop
when the one you want is displayed.
● If you select a Wipe/Fader effect for an Edit-Out point, the
effect is automatically applied to the following Edit-In point.
● You cannot use a Picture Wipe/Dissolve at the end of the
last scene.
● When you use Fader/Wipe effects, that time is included in
the total time.
11 If using Playback Special Effects, press EFFECT.
(੬ pg. 22)
12 Repeat steps 8 through 11 to register additional
scenes.
● To change previously registered points, press CANCEL on
the remote control. The registered points disappear, one at
a time, from the most recently registered point.
● If you are not using Wipe/Fader or Program AE with special
effects, repeat steps 8 and 9 only.
NOTES:
● When choosing a scene, set Edit-In and Edit-Out points so
that there is a relatively large difference between them.
● If the search time for an in-point exceeds 5 minutes, the
recording deck’s Record-Standby mode will be cancelled
and editing will not take place.
● If there are blank portions before or after the Edit-In and
Edit-Out points, a blue screen may be included in the edited
version.
● Turning off the camcorder’s power erases all registered
Edit-In and Edit-Out points.
● If you select Sepia or Monotone mode from Program AE
with special effects, you cannot use the Black & White
Fader. In this case the Black & White indicator begins
blinking. Once the next Edit-In point is registered, the effect
is turned off. To combine these effects, use Sepia or
Monotone during recording, then use the Black & White
Fader during Random Assemble Editing.
● It is not possible to use Wipe/Fader effects and Program AE
with special effects during Random Assemble Editing using
a DV cable.
Automatic Editing To VCR
13 Rewind the tape in the camcorder to the beginning
of the scene you want to edit and press PAUSE (9).
14 Press VCR REC STBY (79) on the remote control,
or manually engage the VCR’s Record-Pause mode.
15 Press the Recording Start/Stop Button on the
camcorder. Editing proceeds as programmed, right
through to the end of the last registered scene.
● When dubbing is complete, the camcorder enters the
Pause mode, and the VCR enters its Record-Pause mode.
● If you do not register an Edit-Out point, the tape will be
dubbed all the way to the end automatically.
● If you operate the camcorder during automatic editing, the
VCR will enter its Record-Pause mode and automatic
editing will stop.
16 Engage the Stop modes for the camcorder and the
VCR.
● To make the R.A.Edit counter display disappear, press
R.A.EDIT ON/OFF on the remote control.
NOTES:
● Pressing R.A.EDIT ON/OFF on the remote control clears
all settings registered during Random Assemble Editing.
● When the editing cable is connected to the remote control’s
PAUSE IN connector during dubbing, make sure the remote
control is pointed at the VCR’s sensor, and the path
between the two is unobstructed.
● Random Assemble Editing may not function properly when
using a tape including several duplicated time codes.
(੬ pg. 19)
PLAY
CANCEL
R.A.EDIT
ON/OFF
FADE/WIPE
EFFECT
EDIT IN/OUT
VCR REC STBY
PAUSE
RM-V717U (optional)
1
2
3
4
5
6
7
8
––: –– ~
~
~
~
~
~
~
~
–
–
:
––
0
:
000
––
TOTAL
CODETIME
NIOUT
MODE
Selected parameter
GR-DZ9_DZ7US.book Page 46 Tuesday, May 18, 2004 10:15 AM