Filter
Top Products
42
Shooting
You need to adjust white shading when you change the lens.
Even if white balance is adjusted in the center of the screen,
the top and bottom of the screen may not be adjusted.
In this case, green and yellow colors may appear on the
screen. This is due to the characteristic of the lens.
Correcting this phenomena is known as white shading
adjustment.
Perform this adjustment after adjusting the white balance.
1 Fill the monitor screen with a pattern box of uniform
light source or white (plain) paper shone with uniform
lighting.
2 Set the control of the camera lens as follows.
ASet the aperture to F4 or more such that the iris
achieves optimum brightness.
If the brightness is insufficient even at F4, set to the
optimum brightness by increasing the lighting.
BWhen using zoom lens, set to the center of the zoom
adjustment range.
3 Adjust the white balance of the camera recorder.
(A Page 40 [Memory A Mode (A), Memory B Mode (B)])
4 Set the chroma level of the monitor to the maximum.
5 Check the monitor screen.
● There is no need for adjustment if there is no color at the
top and bottom of the screen.
● If the top of the screen is greenish and the bottom is
reddish or vice versa, continue this adjustment.
6 Adjust the white shading.
It is recommended to adjust only G (green).
ASet [Main Menu]B[Camera Process]B[White
Balance]B[Shading Mode] to AManualB. (A Page 79)
BSelect [Adjust] in the [White Balance] menu and press
the Set button (R).
CSelect the item to change with the cross-shaped button
(JK) and press the Set button (R).
DChange the setting value with the cross-shaped button
(
JK) while looking at the evaluated value at the bottom
right of the LCD monitor or viewfinder screen.
● If the evaluated value of the adjusting channel is larger
than 0, use the cross-shaped button (
K) to change the
setting value so that the value is more or less AEvenB.
Similarly, if the value is smaller than 0, use the cross-
shaped button (
J) to change the setting value.
(A Page 42 [Evaluated value])
(Adjustment range : Min (-128) to Normal to Max(127))
Memo:
● There may be some delay in the changes of the evaluated
value after pressing the cross-shaped button (
JK).
● Increasing the setting value suppresses the colors at the
bottom and enhances the colors on top.
EPress the Set button (R) to save the settings after the
changes are complete.
FSelect [Back] and press the Set button (R) to return to
the [White Balance] menu.
7 Press the [MENU] button to return to the normal
screen.
8 Readjust the white balance. (A Page 40)
Note:
● If the lens setup is incorrect, you may over-correct the
white shading. Set to the recommended settings for the
lens. (Do not open the iris more than F4. Do not adjust the
zoom lens at the telephoto or wide angle end.)
● White shading occurs as a result of the optical
characteristic of the attached lens. This is not a camera
malfunction.
Adjusting the White
Shading
Cross-Shaped
Button (JK)
Set Button (R)
[MENU] Button
[R] Red adjustment
[G] Green adjustment
[B] Blue adjustment
Evaluated value
A value that compares the average values of the R, G, B
channels in the evaluated value detection frames at the top
(Top) and bottom (Btm) of the LCD monitor or viewfinder
(difference between [Top] and [Btm]).
If [Top] is larger than [Btm], a negative value is displayed. If
[Top] is smaller than [Btm], a positive value is displayed.
When there is no difference between [Top] and [Btm],
AEvenB is displayed. Set such that the evaluated value is
more or less AEvenB.
To p
Btm
CD
F
Evaluated Value Detection Frames
Evaluated
Value