Filter
Top Products
51
Adjustments and Settings for Recording : Assigning Functions to USER MAIN, USER1 and USER2 Buttons
Adjustments and Settings for Recording
The USER MAIN, USER1, and USER2 buttons can be
assigned user-selected functions.
To select desired functions, use the menu options USER
MAIN SW, USER1 SW and USER2 SW. These options
can be found in the <USER SW> screen, which is
accessible from the CAM OPERATION page.
INH: No function assigned.
S.GAIN: S.GAIN function assigned.
DS.GAIN: DS.GAIN function assigned.
LINE MIX GAIN:
LINE MIX GAIN function (+6 dB) assigned.
S.IRIS: Super Iris function assigned.
This is useful for backlight compensation.
I.OVR: Iris Override function assigned.
The target (reference) value in Auto Iris
mode must be changed.
To change the target value, put the unit into
this mode and press the JOG dial button.
Turn the JOG dial button clockwise or anti-
clockwise to change the value. The iris
indication section of the viewfinder screen
displays
“+”, “+ +”, “–”, or “– –”.
When the desired value is displayed, stop
turning the JOG dial button. Then, press the
dial button to accept that value.
Note that once the mode is cancelled or the
power is turned off the original reference
value will be used again.
+: Iris opens up by 0.5.
+ +: Iris opens up by 1.
–: Iris closes down by 0.5.
– –: Iris closes down by 1.
No indication
:The reference value is used.
S.BLK: Super Black function assigned.
This function lowers the black level to the
pedestal level or below.
B.GAMMA: The BLACK gamma function is allocated.
This function highlights the black gradations.
Regardless of the value set in the BLACK
GAMMA item on the menu (<LOW
SETTING> screen, <MID SETTING> screen
and <HIGH SETTING> screen on the PAINT
page), the BLACK GAMMA is set to “+3”.
D.ZOOM: When the digital zoom function is active the
view angle expands by double, triple or 4
times horizontally and vertically. When the
digital zoom function is turned on, the DTL
function is disabled.
ATW: Auto-tracking white balance function
assigned.
Y GET: Function of indicating the brightness level of
the center marker assigned.
DRS: The function of the dynamic range stretcher
is allocated.
The function is allocated to compress the
video level with high brightness and
stretched the dynamic range.
Notes
z Since the DRS function compresses the
video levels of sections with high
brightness, there are slight differences in
color development when the DRS function
is turned on/off.
z When the DRS function is turned on, the
Knee function and the BLACK GAMMA
function are not available.
z The DRS function may be degraded when
the LINE MIX gain and D. ZOOM functions
are enabled at the same time.
ASSIST
The function to turn on or off the assigned
focus assist indication.
Note
When the ASSIST button is turned on, a
graph is displayed on the viewfinder and the
bottom right of the LCD monitor. Adjust the
focus ring on the lens so that the graph
comes further right.
C. TEMP
The function to switch to the mode that
allows the JOG dial button to change the
assigned color temperature. It is useful for
intentionally changing the color temperature
after adjusting the white balance. To change
the color temperature, press the user button
with this assigned function, and then press
the JOG dial button. The color temperature
indicated on the viewfinder display is
highlighted and starts blinking, indicating
that the color temperature can be changed.
While the indication is blinking, the JOG dial
button can be turned to change the color
temperature. At this time, the value set for
the position (PRST, A, or B) to which the
WHITE BAL switch is set is also changed.
Assigning Functions to USER MAIN, USER1
and USER2 Buttons
Selectable Functions
< USER SW >
#
USER MAIN SW :SLOT SEL
USER1 SW :S.GAIN
USER2 SW :DS.GAIN
AJ-HPX2000P(VQT1D27-1)E.book 51 ページ ２００７年７月３０日 月曜日 午後１時３１分