Filter
Top Products
Administrating the Camera
Setting the Camera Image — Camera Menu
41
• The maximum size of a cropped image is 1280 × 720
(SNC-CH210/DH210/DH210T)/1280×960
(SNC-CH110) pixels.
To crop an image
1
Set Cropping to On and click the Area setting
button.
The area setting window appears.
2
Setting the trimming portion
Hold down the left button of the mouse on the still
image and drag the cursor diagonally. The area in a red
frame is the trimming portion.
3
Click OK at the bottom of the window.
The cropped image is displayed on the main viewer.
4
To close the image, click in the upper-right
corner.
SolidPTZ
Select ON to enable the SolidPTZ function.
Notes
• SolidPTZ is not available when Cropping is enabled.
•When Aspect ratio in the System menu- Installation
tab is set to 16:9, this function is not available.
•When SolidPTZ is set to On, the motion detection
function is not available.
•When SolidPTZ of Image 1 is set to On, SolidPTZ
of Image 2 can be set to On.
SolidPTZ priority
When SolidPTZ is set to On, select Resolution or
Frame rate. When you use the SolidPTZ function,
select Resolution to zoom the image clearly, or select
Frame rate to shoot high-speed subjects.
Notes
• SolidPTZ priority setting is not available on the
SNC-CH110.
• You cannot select SolidPTZ priority for Video 2
since the setting value for Video 1 is applied to Video
2.
Codec
Select JPEG, MPEG4, H.264 or OFF. Note that Image
1 cannot be set to Off.
Notes
• The selectable size of images and frame rate for
Image 2 may be limited depend on the setting of codec
type, size of images and/or frame rate for Image 1.
• Motion detection function is not available when Image
2 is set to other than Off.
Image size
You can select the size of images sent from the camera.
The selectable image sizes depend on the aspect ratio
setting in the installation tab. For details on selecting
aspect ratio, refer to “Installation tab” in “System menu”
in page 36.
The selectable image sizes for Image 1 and Image 2 are
as follows:
Notes
• 2048 × 1536 image size can only be selected when the
codec is JPEG.
• Some image sizes for Image 2 cannot be configurable
if the size is not the same as Image 1.
Therefore, when an image size of Image 1 is changed,
the image size of Image 2 may be changed
automatically.
Aspect ratio [4:3]
a: Configurable. ×: Not configurable. f: Configurable
only when Image 1 is this image size.
SNC-CH210/DH210/DH210T
Image 1 Image 2
2048 × 1536 a ×
1920 × 1080 × ×
1600 × 1200 a ×
1680 × 1056 × ×
1440 ×
912 × ×
1376 ×
768 × ×
1280 ×
1024 a ×
1280 ×
960 a ×
1280 ×
800 × ×
1280 ×
720 × ×
1024 ×
768 af
1024 ×
576 × ×
800 ×
480 × ×
768 ×
576 af
720 ×
576 af
704 ×
576 af
720 ×
480 af
640 ×
480 aa
640 ×
368 × a
384 ×
288 aa
352 × 288 aa
320 ×
240 aa
320 ×
192 × a
176 × 144 aa