Filter
Top Products
2. CONTROLS, INDICATORS AND CONNECTORS
30
Ⅲ Alarm Message Display
The following alarm messages are displayed on the status 0 and status 1
screens.
Event display is not made when an alarm message is displayed in alarm
message display 2.
2-10 Indications in Viewfinder (Cont'd)
ACCU- FOCUS
G
F
I
F5.6
STBY 4V21.<60
B
CH1-----+--
CH2-----+--
Alarm message display
1
Alarm message display
2
Indication Contents
CLOSE CASSETTE COVER The cassette cover is not closed.
VTR WARNING [HEAD] Head clogging
VTR WARNING [SERVO] Servo error
1
VTR WARNING [DEW] Condensation
VTR WARNING [HARD] Hardware error
VTR WARNING [STOP] Operation stopped
VTR WARNING [REW] Rewinding abnormality
TAPE NEAR END Remaining tape time is less than about 2 minutes in the record mode
TAPE END Tape end reached
2 REC INHIBITAn unrecordable videocassette (the switch on the back of the cassette is
set to SAVE) is inserted.
NO TAPE VTR trigger is pressed with no tape loaded.
Ⅲ Time/Date Display
When setting DISPLAY item of the TIME DATE menu screen to ON, the time
and date will appear as shown in the diagram on the left. The time and date
are recorded on tape during recording as well.
For the display formats of the time and date, ☞ see page 84.
For setting the time and date, see page 43.
ACCU-FOCUS
G
F
I
F5.6
STBY
REC2
EXT
4V21.>60
B
CH1-----+--
CH2-----+--
2000/06/15
20 :15:15
SD
:213C
Time/date display
29
2. CONTROLS, INDICATORS AND CONNECTORS
8
(Example)
CH1- - - - + - -
CH2- - - - + - -
9
STBY
SAVE
STOP
REC
FF
REW
EJECT
0
(Example)
< 60
(Example)
12: 34: 56: 20
A
(Example)
12.4V
B
F-number:
OPEN, F2, F2.8, F4,
F5.6, F8, F11, F16,
CLOSE
FILTER:
FIL1, FIL2, FIL3
C
(Example)
M: 099
D
EXT, INT, PARA
E
REC2
Shows the input level of the audio input channel.
Display ON/OFF can be selected using the VF DISPLAY menu screen.
☞ See "AUDIO DISPLAY" on page 78.
VCR in standby mode
VCR in save mode
VCR in stop mode
VCR in record mode
VCR in fast-forward mode
VCR in rewind mode
VCR in eject mode
Remaining tape indication (displayed in 1-minute steps)
When the tape is used for a long time, the remaining tape may not be
indicated accurately. At the beginning of the tape, in particular, the indication
may show smaller value than the actual one.
Time code display
Time code display is available when the "REC TIME" item on the VF DISPLAY
menu screen is set to TIME CODE.
☞ See "REC TIME" on page 78.
Voltage indication (displayed in 0.1 V steps) The indicator flashes when the
battery is low. The indicator will not appear when the camera remote control
unit is connected.
The F-number of the connected lens or the filter position of the unit is displayed.
Whether to display the F-number or filter position, or no display is selected in
F. NO/FILTER of the VF DISPLAY screen.
• The F-number may not be displayed depending on the lens type or when
the lens is removed. ☞ See page 78
Not displayed during external video signal input or IEEE1394 input.
In the Super Scene Finder (S.S.F.) mode, the number of memorized scenes
is shown.
M: In MARK mode
C: In CUE mode
Number: Number of memorized scenes
Displays whether the main unit is used for recording or the external VCR
connected to the VTR/RM multi-pin connector.
The displays will differ depending on the VTR SELECT switch setting.
INT is constantly displayed during external video input or IEEE1394 input.
INT is constantly displayed when the VTR/RM switch is set to RM.
The display will light during external VCR recording.
The display flashes when there is a warning on the external VCR.
The display will not appear when the VTR/RM switch is set to RM.
2-10 Indications in Viewfinder (Cont'd)
●
Status 1
In addition to the information on the Status 0 screen, this screen displays audio indicators and information on remaining
tape, voltage and lens F-number (or FILTER POSITION).
Indication Indication Contents
SCENE FILE A, B, OFF
WHITE BAL A, B, PRESET, FAW, MANUAL (When remote control unit w/manual balance is connected.)
FILTER 3.2K, 5.6K+1/8ND, 5.6K+1/64ND
SHUTTER OFF, 1/100 (U)/1/120(E), 1/250, 1/500, 1/1000, 1/2000, 1/60.1 (U)/1/50.1 (E) to 1/2084.6 (U)/
1/2067.8 (E) (in VARIABLE mode), EEI (in ALC mode)
GAIN -3dB, 0dB, 3dB, 6dB, 9dB, 12dB, 18dB, LOLUX, ALC
IRIS LEVEL NORMAL, BACK L, SPOT L
FULL AUTO ON, OFF
REC TIME Remaining tape time or time code.
●
Status 2 ... Not displayed during external video signal input or IEEE1394 input.
This screen displays the camera setup statuses.
Event display is not available while this screen is displayed.
Display position
Function
Display
When the RS-232C cable
is connected, the VCR
operation mode may not
be displayed correctly.
Note: