Filter
Top Products
10. S.S.F. (Super Scene Finder) FUNCTION
68
SHUTTER
STATUS
MENU
FILTER
3200k
1
5600k+1/8ND
2
5600k+1/64ND
3
ALARM
MONITOR
OPERATE
NG
GAIN
OUTPUT
WHT.BAL
VTR
ON OFF
AUTO IRIS
LOLUX
BACK L
NORMAL
SPOT L
STRETCH
NORMAL
COMPRESS
LIGHT
ON
OFF
COUNTER
AUDIO SELECT
MANUAL
AUTO
CH-1 CH-2 CH-1 CH-2
REAR
FRONT
RM
AUDIO INPUT
MODE
CTL
TC
UB
CH-1
MIX
CH-2
RESET
OPERATE/WARNING
MONITOR
SELECT
CH-1
AUDIO
LEVEL
CH-2
VTR
ON
OFF
INCOM
MIC
INCOM
MIC
LEVEL
POWER
OFFRM
DC IN
/BATT.
CALL
CARBON
DYNAMIC
FULL AUTOBLACK
NG button
10-3 Deleting S.S.F. Data
1.
Press the STOP button to enter the stop mode.
2.
Press the RESET button while the LOG button is kept
pressed.
• All the S.S.F. data held in the memory are erased.
However, the reel number is not cleared.
10-4 Resetting S.S.F. Data
Operation
SHUTTER
STATUS
MENU
FILTER
3200k
1
5600k+1/8ND
2
5600k+1/64ND
3
ALARM
MONITOR
OPERATE
NG
GAIN
OUTPUT
WHT.BAL
VTR
ON OFF
AUTO IRIS
LOLUX
BACK L
NORMAL
SPOT L
STRETCH
NORMAL
COMPRESS
LIGHT
ON
OFF
COUNTER
AUDIO SELECT
MANUAL
AUTO
CH-1 CH-2 CH-1 CH-2
REAR
FRONT
RM
AUDIO INPUT
MODE
CTL
TC
UB
CH-1
MIX
CH-2
RESET
OPERATE/WARNING
MONITOR
SELECT
CH-1
AUDIO
LEVEL
CH-2
VTR
ON
OFF
INCOM
MIC
INCOM
MIC
LEVEL
POWER
OFFRM
DC IN
/BATT.
CALL
CARBON
DYNAMIC
FULL AUTOBLACK
LOG
REW
FF
PLAY
STILL
STOP
2.
LOG button
1.
STOP button
2.
RESET button
The S.S.F. data recorded in the unit's memory can be deleted
in the record mode and the record-pause mode.
This function is only valid in the MARK mode.
Ⅲ In the record mode, press the NG button after the IN point or
OUT point has been stored.
• When pressed after the IN point has been stored, the S.S.F.
data of the scene being recorded are deleted. When
pressed after the OUT point has been stored, the S.S.F.
data of the immediately preceding scene are deleted.
When the NG button is used for deleting operation, the
next scene number is updated to a new number.
Ⅲ In the record-pause mode, press the NG button.
The S.S.F. data of the immediately preceding scene are
deleted.
The NG button is only valid for the immediately preceding
scene. The erase of scene data by the NG button cannot
be confirmed on the unit.
Note:
10. S.S.F. (Super Scene Finder) FUNCTION
67
CUE Mode
1.
Set the S.S.F. mode as CUE mode.
Set the VCR Setup Menu item No. 398 S.S.F. MODE to
"CUE".
☞ See page 75.
• The CUE mode is indicated in the lower part of the Status
1 screen in the viewfinder.
MARK Mode
1.
Set the S.S.F. mode as MARK mode.
Set the VCR Setup Menu item No. 398 S.S.F. MODE to
"MARK".
☞ See page 75.
• The MARK mode is indicated in the lower part of the
Status 1 screen in the viewfinder.
VF
AUTO
WHITE
SKIN
AREA
ACCU
FOCUS
TAKE
VTR
PUSH
ZEBRA
AUDIO
LEVEL CH-1
ON
OFF
TAKE button
VTR trigger button
2.
Press the VTR trigger button to start the recording.
3.
When you reach the point that you want to memorize as
the CUE point, press the TAKE button.
• The time code data of the point where the TAKE button is
pressed is stored in the unit's memory as CUE data.
The LOG button’s LED lights during memorization of the
CUE point and the “∗” mark is shown in the viewfinder.
Ⅲ Press the TAKE button each time you reach a point that
you want to memorize as CUE data.
4.
Stop the recording.
Press the VTR trigger button.
2.
Press the VTR trigger button to start the recording.
3.
When you reach the scene that you want to memorize, press
the TAKE button.
• The time code data of the point where the TAKE button is
pressed is stored in the unit's memory as the start point
of the scene.
4.
When you reach the scene that you want to memorize as
the ending point, press the TAKE button again.
• The time code data of the point where the TAKE button is
pressed is stored in the unit's memory as the ending point
of the scene.
• The LOG button’s LED lights during memorization of the
IN point and the “∗” mark is shown in the viewfinder.
The LOG button’s LED remains off during memorization
of the OUT point and the “∗” mark is not shown in the
viewfinder.
Ⅲ For each scene that you want to memorize, repeat steps
3.
and
4.
5.
Stop the recording.
Press the VTR trigger button.
10-2 How to Use the S.S.F. Function
ACCU -FOCUS
G
F
I
F5.6
STBY 4V21.<60
B
SD
CH1-----+--
CH2-----+--
C: 909
ACCU -FOCUS
G
F
I
F5.6
STBY 4V21.<60
B
SD
CH1-----+--
CH2-----+--
M: 909
Number of
memorized
scenes
MARK mode
Number of memorized
scenes
* This indicator is not
indicating the number
of the CUE point.
CUE mode
• Once a tape with recorded S.S.F. data is rewound but not ejected before playback or recording is performed on it again, the
previous S.S.F. data cannot be automatically erased when S.S.F. data are recorded (when you overwrite the previous image).
Therefore, the S.S.F. data of the overlapped sections will not correspond to the video image.
Furthermore, please note that the time code data may differ from the actual data if recording is started in the CUE mode in
this situation.
Note: