Filter
Top Products
81
Adjustments and Settings for Recording
: Viewfinder Screen Status Displays
Adjustments and Settings for Recording
Information Item Indication Status
13. System
information and
warnings
SYSTEM ERROR- Something abnormal is happening to the internal computer communications or
reference signal. No further recording or playback can be performed. is
replaced with an error code. For more information, see [Error Codes]
(page 163).
TURN POWER OFF P2 card has been removed while being accessed (recorded, played back, or
formatted), and subsequent operation is disabled.
CARD ERR An error has occurred while recording data to or playing data from a P2 card. In
the actual indication the is replaced by the slot number of the P2 card that
triggered the error.
REC WARNING Something abnormal is happening to video and/or audio being recorded.
BACKUP BATT EMPTY Backup battery needs replacing.
FAN STOP The fan is locked and halted.
WIRELESS-RF RF signal from the wireless receiver is degraded.
EOM P2 card has no free space.
BOS Playback position is at the start of all the clips.
EOS Playback position is at the end of all the clips.
CANNOT REC Indicates that it is not possible to record to a P2 card directly after insertion or
switching on the power. Detailed information is provided on the FUNCTION
screen of MODE CHECK. See the relevant section of the 10. MODE CHECK
indication area.
CANNOT PLAY Clip cannot be played back perhaps because no P2 card is loaded, or the P2
card contains no clips.
COMM ERROR Displayed when disconnection between microcomputers continues for a
specified period or longer.
TEXT MEMO Text memo has been added.
TEXT MEMO INVALID Text memo has not been successfully added.
MARK ON/OFF Shot mark has been added or deleted. For information on shot marks, see
[Shot Mark Function] (page 48).
SHOT MARK INVALID This is displayed when shot marks cannot be added.
UPDATING Clip information is being updated. Playback operation disabled.
USB DEVICE The unit is in USB DEVICE mode. When communication is disabled, the
indication blinks.
USB HOST Indicates that the unit is set to the USB HOST mode. When the external hard
disk is not successfully recognized, then the indication blinks.
THUMBNAIL OPEN Thumbnail is being manipulated.
PROXY REC P2&SD Displayed when proxy recording on either the P2 card or the SD memory card
starts (when AJ-YAX800G is attached, the PROXY REC item on the <VF
INDICATOR3> screen is turned on).
PROXY REC P2 Displayed when proxy recording on the P2 card starts (when AJ-YAX800G is
attached, the PROXY REC item on the <VF INDICATOR3> screen is turned
on).
NEAR END (SD) When the remaining free space on the SD Memory card drops below 1 minute
during proxy recording, the message is displayed (when AJ-YAX800G is
attached).
EOM (SD) Displayed when full capacity is reached during proxy recording on the SD
memory card (when AJ-YAX800G is attached).
PROXY CARD ERROR Displayed when proxy recording stops because of failure on either the video
encoder card or the stream. Check the video encoder card or avoid use of
proxy recording. (When AJ-YAX800G is attached.)
SD CARD WRITE ERR Displayed when a failure occurs on the SD memory card during proxy
recording, and only recording on the SD memory card stops (when AJ-
YAX800G is attached).
TC REGEN The RET button was pressed to regenerate the time code as the time code for
the last clip recorded on a P2 card.
SLOT SEL This blinks while the recording slots of P2 cards are switched after pressing the
user button where the SLOT SEL function is assigned.
SLOT SEL INVALID This is displayed if the recording slots of P2 cards cannot be switched when
the user button where the SLOT SEL function is assigned is pressed.
DIR NG CARD
SLOT1/2/3/4/5
This is displayed when a P2 card with an irregular directory structure is
inserted or when beginning or ending a recording to an inserted card having
such a directory structure.
RUN DOWN CARD
SLOT1/2/3/4/5
This is displayed when the recording starts or completes with a P2 card on
which the maximum number of overwrites has been exceeded, or when data is
recorded after inserting such a P2 card.
AUDIO NOT RECORDING This is displayed when audio is not being recorded on the P2 card even if the
audio level meter is moving.
AJ-HPX3700G-VQT1V68_eng.book 81 ページ ２００８年１０月１５日 水曜日 午後６時３８分