Filter
Top Products
12
Introduction
A LCD cover
B
[COMPONENT OUT] Component output terminal
(
A
Page 91)
C
[A/V OUT] Audio/Video output terminal (
A
Page 91)
D
[C.REVIEW/4] Clip Review/User 4 button (
A
Page 28)
For checking the most recently captured images.
You can also use it as a user button by assigning a specific
feature in the menu setting to this button. (A Page 19)
E
[ZEBRA/5] Zebra/User 5 button (
A
Page 32)
For displaying or canceling the display of zebra pattern
based on the luminance of the object. You can also use it as
a user button by assigning a specific feature in the menu
setting to this button. (A Page 19)
F
Built-in speaker (
A
Page 39)
Adjust the volume with the [ADJ./VOL.] knob on the rear.
Memo :
●
The built-in speaker is usable only in the Media mode. Audio
is not output from the built-in speaker during Camera mode.
●
Audio level in the Camera mode and Media mode can be
adjusted separately.
●
When in the Media mode, the volume of the headphone and
speaker are adjusted at the same time.
● The built-in speaker cannot be used when the [HDMI]
terminal, [A/V OUT] terminal, or headphone jack is
connected.
G
[SLOT SEL] Slot selection button (
A
Page 25)
For switching the active card slot during shooting and
playback.
H
[LOLUX/3] Low-light shooting/User 3 button (
A
Page 19)
For switching the low-light shooting mode ON or OFF.
You can also use it as a user button by assigning a specific
feature in the menu setting to this button. (A Page 19)
I
[DISPLAY] Display button
For switching the displays on the LCD screen and viewfinder.
(A Page 20)
J
[REC] Record trigger button (
A
Page 27)
Button for starting or stopping recording.
K
LCD monitor (
A
Page 20)
L
[MENU/THUMB] Menu/Thumbnail button
The operation changes according to the status of the camera
recorder.
During Camera mode: Displays the menu screen. Press
again to exit the menu.
During Media mode: During media playback, the thumbnail
screen is displayed.
During thumbnail screen display, the thumbnail menu is
displayed.
M
Set lever
When in the Camera mode, this lever is used for Program AE
selection and as the zooming lever. (A Page 30)
When in the Media mode, this lever is used for clip selection
and playback control. (A Page 48)
When the menu screen is displayed, this lever is used for
menu setting. (A Page 58)
Ⅵ Bottom
N
Tripod mounting holes (
A
Page 15)
Memo :
● To prevent the camera recorder from falling, attach
securely using the rotation prevention hole.
● Use screws with screw length 5 mm and below.
Names of Parts (continued)
CH-2 INPUT
CH-1
3
4
5
2
1
2
3
0
CH-2
AUDIO INPUT
AUTO MANUAL
AUTO MANUAL
USER1
AB
FOCUS
ZOOM
ON
ND
FILTER
OFF
USER2
AF/MF FULL AUTO
AUDIO
SELECT
INPUT1
INPUT2
- LINE -
- MIC -
MIC+48V
INPUT1
INPUT2
GAIN
L-
M-
H-
B-
A-
PRST-
WHT.BAL
IRIS A/M
C.REVIEW/4 ZEBRA/5
SLOT SEL
DISPLAY
COMPONENT
OUT
A / V OUT
LOLUX/3
MENU/
THUMB
T
W
REC
P
R
O
G
R
A
M
A
E
B
D
C
E
A
FGHI
J
KLM
N
Ⅵ LCD Monitor
When the LCD cover is opened
Bottom
GY-HM150U.book Page 12 Monday, September 5, 2011 1:48 AM