Filter
Top Products
105
8
Chapter 8 Menu Description Tables (continued)
8-3-7 ADDITIONAL DTL 8-3-8 SKIN TONE DTL
<Note>
The items indicated by are the setting items for PAINT
MENU SW() R/W in the <SD CARD R/W SELECT>
screen. The items without are the setting items for PAINT
MENU LEVEL R/W.
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
The ____ in the Adjustable Range column indicates the
preset mode.
Items/
Data Saved
Adjustable
Range
Remarks
KNEE APE LVL OFF
1
2
:
5
Set KNEE APE LEVEL.
SCUFE
CHROMA DTL OFF
1
:
5
Set the chroma detail.
Detects the chroma edge and
superimposes it on Y to enhance
H.DTL. A greater value increases the
correction.
SCUFE
DTL GAIN(+) –31
:
+00
:
+31
Adjust the detail level toward +
(upwards).
SCUFE
DTL GAIN(–) –31
:
+00
:
+31
Adjust the detail level toward the –
(downwards).
SCUFE
DTL CLIP 00
:
63
Adjust the detail signal clip towards the
+ direction.
SCUFE
DTL SOURCE (R+G)/2
(G+B)/2
2G+R+B /4
(3G+R)/4
R
G
Set the signal source for detail signal
components.
SCUFE
H.DTL LINE MIX 0H
1H
2H
Set the scan line to generate the H.DTL
signal.
SCUFE
CORNER DTL ON
OFF
ON/OFF switching for CORNER DTL
mode, which enhances the resolution
around the screen perimeter.
SCUFE
Items/
Data Saved
Adjustable
Range
Remarks
SKIN TONE
DTL
ON
OFF
Set the skin tone DTL to ON or OFF.
SCUFE
SKIN TONE
ZEBRA
ON
OFF
ON/OFF switching for ZEBRA within
the SKIN TONE range.
SCUFE
SKIN DTL
CORING
0
:
5
:
7
Adjust the effect of SKIN TONE DTL
CORING.
SCUFE
SKIN TONE
GET
Used when obtaining the target hue for
SKIN TONE DTL. Align the center
marker and the target object with each
other.
–––––
Y MAX 000
:
190
:
255
Set the maximum value of the
brightness signal to which SKIN TONE
effect is enabled.
SCUFE
Y MIN 000
:
010
:
255
Set the minimum value of the
brightness signal to which the SKIN
TONE effect is enabled.
SCUFE
I CENTER 000
:
022
:
255
Set the center position on the I axis (the
area where SKIN TONE is enabled).
SCUFE
I WIDTH 000
:
010
:
255
Set the area width where SKIN TONE
is enabled along the I axis above and
below the I CENTER.
SCUFE
Q WIDTH 000
:
005
:
255
Set the area width where SKIN TONE
is enabled along the Q axis above and
below the I CENTER.
SCUFE
Q PHASE –128
:
+000
:
+127
Set the phase in the area where SKIN
TONE is enabled based on the Q axis.
SCUFE
R-Y
B-Y
Q-WIDTH
I-WIDTH
Q-PHASE
I-CENTER
Y
Y-MAX
Y-MIN
0
– direction
+ direction
= SKIN TONE AREA
#,52%2'PINKUJDQQMࡍࠫ㧞㧜㧜㧢ᐕ㧡㧝㧝ᣣޓᧁᦐᣣޓඦ೨㧥ᤨ㧠㧡ಽ