Filter
Top Products
67
Others
4 If the image is not still clear, repeat Steps 1
to 3. (Do not use the Head Cleaner 3 times or
more consecutively.)
Notes:
• Do not rewind every time you use the Head Cleaner.
Rewind only when the tape reaches the end, and
then use it again from the beginning in the same
manner as before.
• If the heads become dirty soon after cleaning, the
tape may be damaged. In this case, immediately
stop using that Cassette.
• Do not clean the heads excessively. (Excessive
cleaning may cause excessive wear of the heads. If
the heads are worn, images cannot be played back
even after the heads are cleaned.)
• If the dirty heads cannot be cleaned with the Head
Cleaner, the Camcorder needs to be cleaned at a
Servicenter. Please consult a dealer.
• Head cleaning due to dirty heads is not considered
a malfunction of the product. It is not covered by the
warranty.
Periodical Check-up
To maintain the highest image quality, we recommend
replacement of worn parts, such as heads, etc., after
approximately 1000 hours of use. (This, however,
depends on operating conditions, such as temperature,
humidity, dust, etc.)
Optimal Use of the Battery
Battery Characteristics
This Battery is a rechargeable lithium ion battery. Its
ability to generate power is based upon the chemical
reaction that takes place inside it. This reaction is
susceptible to the surrounding temperature and humidity,
and, if the temperature is too high or too low, the
operating time of the Battery becomes shorter. If the
Battery is used in an extremely cold environment, the
Battery may operate only for about 5 minutes. If the
Battery becomes extremely hot, a protective function
may operate, and the Battery may become unusable
for a while.
Be Sure to Detach the Battery after Use
Be sure to detach the Battery from the Camcorder. (If
it is left attached to the Camcorder, a minute amount
of current is consumed even when the Camcorder
power is off.) If the Battery is left attached to the
Camcorder for a long time, over-discharge takes
place. The Battery may become unusable after it is
charged.
Disposing of an Unusable Battery
• The Battery has a limited life.
• Do not throw the Battery into fi re because it may
cause an explosion.
Always Keep the Terminals of the Battery Clean
Prevent the terminals from getting clogged with dirt,
dust, or other substances. If you drop the Battery
accidentally, check to see if the Battery body and
terminals are deformed. Attaching a deformed Battery
to the Camcorder or AC Adaptor may damage the
Camcorder or AC Adaptor.
1 Remove the tape if it is inserted.
• It takes about 20 seconds to open the Cassette
Holder. This is not a malfunction.
2 Leave the Camcorder with the Cassette
Compartment Cover closed to cool or warm
it to the ambient temperature.
When [
DEW ] blinks in yellow
• You cannot use the Tape Recording/Playback
Mode. Leave the Camcorder for about 30 minutes.
• However, you can use the Card Recording Mode
or Picture Playback Mode when the cassette is
not inserted.
When [ DEW ] blinks in red
• The Power Indicator Lamp blinks for about 1
minute and then the Camcorder automatically
turns off. Leave it for about 2 to 3 hours.
3 Turn the Camcorder on again, set it to the
Tape Recording/Playback Mode and then
check if the condensation indication
disappears.
Especially in cold conditions, dew may be frozen. In
this case, it may take more time before the
condensation indication disappears.
Watch for Condensation even before the
Condensation Indication is displayed.
• The condensation indication may not appear
depending on circumstances. When condensation
occurs on the lens or the Camcorder, it also may
occur on the head and the tape. Do not open the
Cassette Compartment Cover.
When the Lens Is Fogged:
Set the [OFF/ON] Switch to [OFF] and leave the
Camcorder in this condition for about 1 hour. When the
lens temperature becomes close to the ambient
temperature, the fog disappears naturally.
Video Head Clogging and Care
If the heads (the parts that make contact with the tape)
are dirty, mosaic-pattern noise may appear on the
playback image, or the screen as a whole becomes
black. If the heads are extremely dirty, recording
performance deteriorates, and, in the worst case, the
Camcorder cannot record at all.
Causes of Dirty Heads
• Large quantity of dust in the air
• High-temperature and high-humidity environment
• Damaged tape
• Long operating hours
Using Panasonic cleanig cassette (AY-DVMCLA)
1 Insert the Head Cleaner into the Camcorder
in the same manner as a Video Cassette.
2 Press the [►] Button, and approximately 20
seconds later, press the [
] Button. (Do not
rewind the tape.)
3 Take out the Head Cleaner. Insert a Video
Cassette and start recording. Then, play the
tape back to check the recorded image.