Filter
Top Products
Camera Settings (CAMERA)
17
Further emphasizes the profile of the target object. The amount of
compensation can be adjusted for the horizontal or vertical directions.
1
Use the joystick lever (xy) to select [APERTURE],
use the lever (vw) to select “ON y”, and press the
[ENTER] button.
The APERTURE SETTING screen appears.
Available settings:
•OFF: The profile compensation is turned off.
•ON: The profile compensation is turned on.
2
Use the joystick lever (vw) to adjust the value for
“H” (horizontal).
Available settings: 1 - 15 (The higher the number, the further
the profile is emphasized.)
3
Use the joystick lever (xy) to move the cursor to
“V” (vertical), and use the lever (vw) to adjust the
value for “V”.
Available settings: 1 - 15 (The higher the number, the further
the profile is emphasized.)
☞ After completing adjustment, use the lever to move the
cursor to [MENU] and select “BACK” or “END”.
Sets the AGC (Auto Gain Control) level in four grades.
If you do not use the AGC function, set [AGC] to “OFF”.
1
Use the joystick lever (xy) to select [AGC], use the
lever (vw) to select “ON y”, and press the [ENTER]
button.
The GAIN SETTING screen appears.
Memo: Auto Gain Control (AGC) is a function that automatically adjusts gain
level in the amplifier section for the camera’s video signal according
to the brightness of the target object and keeps the signal output level
constant. When the target object is bright, the gain level is
decreased; when it is dark, the level is increased.
2
Use the joystick lever (xy) to select [MAX GAIN]
and use the lever (vw) to adjust AGC level.
Available settings:
•NORMAL: Initial setting
• MIDDLE: For dark target object
•HIGH: For very dark target object
•LOW: For bright target object
Memo: • The “LOW” option cannot be selected when the Day/Night
function is set to “AUTO”.
• The value for the “MAX GAIN” setting depends on the
Day/Night function mode.
• When the gain level is increased, the sensitivity is
improved in dark condition, but the noise level increases.
3
Use the joystick lever (
xy
) to select [DNR] and use the
lever (
vw
) to select a DNR (Digital Noise Reduction) option.
Available settings:
•ON: Applies DNR.
(Reduces noise during low luminance level.)
•OFF: Does not apply DNR.
☞ After completing setting, use the lever to move the cursor to
[MENU] and select “BACK” or “END”.
F
Setting the profile compensation
(APERTURE)
y
y
y
y
y
SYNC
IRIS
WHITE BALANCE
BLC
SHUTTER
APERTURE
AGC
GAMMA
DAY/NIGHT
PRESET
MENU
INT
AUTO
ATW
OFF
OFF
ON
ON
0.45
AUTO
OFF
BACK
APERTURE SETTING
H 8
V 8
PRESET
MENU
OFF
BACK
G Setting the AGC level (AGC)
Setting AGC
Digital noise reduction operates when the gain level increases. In
addition, blurring and ghosting of images can occur when
moving images are monitored, so the resolution is also reduced
slightly.
When the electronic zoom is operating in the color mode, the
DNR (Digital Noise Reduction) does not function.
y
y
y
y
y
SYNC
IRIS
WHITE BALANCE
BLC
SHUTTER
APERTURE
AGC
GAMMA
DAY/NIGHT
INT
AUTO
ATW
OFF
OFF
ON
ON
0.45
AUTO
GAIN SETTING
MAX GAIN
DNR
NORMAL
OFF
L5BU2_XE(VCC-MC600P_MC500P)(GB).book 17 ページ ２００７年１月１８日 木曜日 午前９時４４分