Sony 900 Camcorder User Manual


 
8
Chapter 8 Connectors and Cables 158HDC-900/950/930 Series Product Information Manual
SMPTE 292M
Analog signal
FRAME REFERENCE IN: BNC
±0.3 V, ternary SYNC, 75 Ohms
Or, black burst signal 0.286 V p-p, 75 Ohms
FRAME REFERENCE OUT: BNC
THROUGH OUT/0.3 V p-p, FRAME SYNC pulse, 75
Ohms
8-3-1-2 CAMERA connector (optical/electrical
composite connector)
VIDEO Y/PB/PR
Conforms to BTA-S004B,
1.485 Gbps/
1.4835 Gbps serial
SMPTE 292M
RET VIDEO Y/PB/PR
Conforms to BTA-S004B,
1.485 Gbps/
1.4835 Gbps serial
SMPTE 292M
INCOM 2ch
MIC 2ch
DIGITAL AUDIO (AES/EBU)
CAMERA COMMAND
PROMPTER
8-3-1-3 MIC1/MCI2 (XLR 3-pin, Male)
(0 dBu = 0.775 Vrms)
8-3-1-4 MIC REMOTE (D-sub 15-pin, Female)
(WF REMOTE (D-sub 15-pin, Female))
In the case of MIC REMOTE mode : S423-3/AT-149 t OFF)
*1 CHU MIC 1/2 AMP GAIN
The setup for the HDCU-700A mode is shown in parenthesis
().
In the case -of theHDCU-700A mode : S423-2/AT-149
t ON
*2
*3
In the case of the WF REMOTE mode : S423-3/AT-149
t ON
Recall system
No. Signal Specifications
1 MIC OUT (G) 0 dBu/-20 dBu
(Selectable with S502,
S503/AVP-4)
2 MIC OUT (X)
3 MIC OUT (Y)
No. Signal Specifications
1 +5.5 V OUT Max. 250 mA
2 TALLY GND GND for TALLY
3 G TALLY OUT ON (GND) : Max. 30 mA
IN
4 R TALLY OUT ON (GND) : Max. 30 mA
IN
5 CHU MIC CONT2
*1
Refer to the below
column.
6 AMP CONT1
*1
Refer to the below
column.
12
3
(External view)
15 9
18
(External view)
7 GAIN IN CONT0
*1
Refer to the below
column.
8 MIC1 GAIN CONT
ON/OFF IN
*2
Refer to the below
column
9 GND GND for +5.5 V
10 TALLY OUT R/G TALLY OUT
ON (GND) : Max. 30 mA
IN
11 NC No connection
12 ASPECT REMOTE
ON/OFF
L : REMOTE
13 ASPECT CONT1
*3
Refer to the below
column.
14 CTL CONT2
*3
Refer to the below
column.
15 MIC2 GAIN CONT
ON/OFF IN
*2
Refer to the below
column
CONT0 CONT1 CONT2 CHU MIC AMP GAIN
H H H 60 dB
L H H 50 dB
H L H 40 dB
L L H 30 dB
H H L 20 dB
8pin 15pin MIC GAIN CONT
L L MIC 1 and 2 ON
LHMIC 1 ON
HLMIC 2 ON
HHINTERNAL set
CONT1 CONT2 ASPECT
L H SQ (16 : 9)
H H EC (4 : 3)
LLINTERNAL set
H L LB (4 : 3)
No. Signal Specifications
1 NC No connection
2 NC No connection
3 NC No connection
4 NC No connection
5 RECALL2 (G) LOW ACTIVE
6 RECALL3 (B) LOW ACTIVE
7 RECALL1 (R) LOW ACTIVE
8 RECALL4 (SEQ) LOW ACTIVE
9GND
10 NC No connection
11 NC No connection
12 RECALL5 (ENC) LOW ACTIVE
13 RECALL6 (R+B) LOW ACTIVE
No. Signal Specifications