Filter
Top Products
37
Menu Operations
To end menu operations
Set the DISPLAY switch to OFF.
Editing the USER Menu
You can select desired pages and items from the
OPERATION, PAINT, MAINTENANCE, FILE, and
DIAGNOSIS menus and register them to the USER menu.
If you specify pages or items frequently used for the USER
menu, you can easily call and use them.
The following pages are included on the factory-set USER
menu:
For the items on each page, see the corresponding source
menu page in the table in “Menu List” on page 41.
The USER MENU CUSTOMIZE menu allows you to
configure a USER menu that consists only of pages and
items that you need, by your adding, deleting or replacing
pages.
Editing by items
The USER MENU CUSTOMIZE menu allows you to add
a new page to the USER menu and add desired items to the
page.
While the EDIT page contains factory-preset items, the
USER 1 EDIT to USER 19 EDIT pages are all blank in
their initial state. You can register up to 10 items, including
blank lines, on each of these pages.
To add items to a page
Proceed as follows.
1
While holding the CANCEL/STATUS switch pressed
toward STATUS, move the DISPLAY switch from the
OFF position to the MENU position.
The TOP MENU screen appears.
2
Turn the MENU SEL knob/ENTER button to move the
arrow marker (
,) to “USER MENU CUSTOMIZE”
then push on the MENU SEL knob/ENTER button.
If this is the first time the USER MENU CUSTOMIZE
menu has been displayed, the CONTENTS page of the
menu appears.
If the USER MENU CUSTOMIZE menu has been
used before, the page last accessed appears.
3
If the CONTENTS page is displayed, turn the MENU
SEL knob/ENTER button to move the arrow marker
(
,) to any of USER 1 EDIT to USER 19 EDIT then
push on the MENU SEL knob/ENTER button to
display the page.
If a different page is displayed, turn the MENU SEL
knob/ENTER button until the desired page appears,
then push on the MENU SEL knob/ENTER button to
select the page.
Example: When you select the USER 2 EDIT page
Menu page title USER
menu
No.
Source menu / page No.
<VF OUT> U01 OPERATION 08
<VF DETAIL> U02 OPERATION 04
<FOCUS ASSIST> U03 OPERATION 05
<VF DISPLAY> U04 OPERATION 01
<‘!’ IND> U05 OPERATION 02
<VF MARKER> U06 OPERATION 03
<CURSOR> U07 OPERATION 07
<ZEBRA> U08 OPERATION 06
<SWITCH ASSIGN1> U09 OPERATION 09
<SWITCH ASSIGN2> U10 OPERATION 10
<POWER SAVE> U11 MAINTENANCE M13
<LENS FILE> U12 OPERATION 18
<HEAD SET> U13 OPERATION 11
<INTERCOM LEVEL> U14 OPERATION 12
<MIC GAIN> U15 MAINTENANCE M06
<OUTPUT FORMAT> U16 MAINTENANCE M09
<TEST OUT> U17 MAINTENANCE M11
<SDI-2 OUT> (HDC1500R)
or <SDI OUT>
(HDC1550R/1400R/1450R)
U18 MAINTENANCE M12
<DOWN CONVERTER> U19 MAINTENANCE M10
<TRUNK> U20 MAINTENANCE M14
<UP TALLY> U21 MAINTENANCE M07
<ROM VERSION> U22 DIAGNOSIS D04
CONTENTS E00
xx
01.EDIT PAGE
02.USER 1 EDIT
c
03.USER 2 EDIT
04.USER 3 EDIT
05.USER 4 EDIT
06.USER 5 EDIT
07.USER 6 EDIT
08.USER 7 EDIT
09.USER 8 EDIT
10.USER 9 EDIT
TOP
USER 2 EDIT E03
c
TOP