Filter
Top Products
135
Setting the Status Display on the Viewfinder Screen and the LCD Monitor
Chapter 5 Menu Displays and Detailed Settings
Setting the Status Display
on the Viewfinder Screen
and the LCD Monitor
This section explains the menu settings for the display of
the viewfinder screen. These settings are also used for the
display of the LCD monitor in the same way.
Selecting the Display Items
To select the items to be displayed on the viewfinder
screen (with the viewfinder DISPLAY switch set to ON)
and the LCD monitor, use the VF DISP 1 and VF DISP 2
pages of the OPERATION menu.
(How to select an item in the menu screen: Turn the
MENU knob to move the b mark to the desired item.)
1
Display the VF DISP 1 or VF DISP 2 page of the
OPERATION menu, and press the MENU knob.
For details on menu operations, see “Basic Menu
Operations” on page 129.
2
Select the desired setting item, and press the MENU
knob.
On the VF DISP 1 and VF DISP 2 pages, you can
select any of the following items to turn its display on
or off.
VF DISP 1 page
1) This item may not appear depending on the mounted lens.
2) When an Anton Bauer battery system or a BP-GL65/GL95 battery
pack is installed, the remaining battery power is shown as a
percentage value (%) according to the setting of this item.
INT: When one of the above batteries is installed, the remaining
power is shown as a percentage value (%) when there is a change
in the value or when the power is low.
AUTO: The remaining power is shown as a percentage value (%)
when one of the above batteries is installed. Otherwise the voltage
(VOLT) is displayed continuously.
VOLT: The voltage (VOLT) is displayed continuously.
VF DISP 2 page
3
Turn the MENU knob to select the desired setting
(ON, OFF, or value), and press the MENU knob.
4
Repeat steps 2 and 3 until you have set all of the
desired items.
Change Confirmation/Adjustment
Progress Messages
The messages indicating setting changes, progress and
consequence of adjustments, and the situations indicated
by these messages are as follows.
Setting change confirmation/adjustment progress
messages
Item Description
DISP REC
FORMAT
Displays the recording format.
DISP BIT RATE Indication of HQ, SP or LP
recording.
DISP SYSTEM System frequency.
DISP 16:9 Aspect ratio indication when
recording SD signals.
DISP ZOOM
1)
Zoom position indication.
DISP FOCUS
1)
Focus setting.
DISP BATT
REMAIN
2)
Displays the battery voltage or
battery remaining capacity.
DISP REC/TALLY REC, PLAY, F REV, and F FWD
indications.
DISP TIM CODE Displays the timecode.
Item Description
DISP 5600K Displays “5600K”.
DISP FILTER Displays types of the ND filter.
DISP WHITE Displays selected white balance
memory.
DISP GAIN Displays gain value.
DISP SHUTTER Displays shutter speed and ECS
mode.
DISP AUDIO Displays audio level.
DISP DISC Displays remaining disc capacity.
DISP IRIS Lens iris setting indication
DISP LOW LIGHT “LOW LIGHT” indication when the
average video level is below a
certain threshold.
DISP INTERVAL “INTERVAL TIME” indication
during interval recording.
Situation Message to appear
The filter selection has been
changed
FILTER: n
(where n = 1, 2, 3, 4)
The gain setting has been
changed
GAIN: n
(where n = –3dB, 0dB, 3dB,
6dB, 9dB,12dB, 18dB, 24dB,
30dB, 36dB, 42dB, 48dB)
The setting of the WHITE
BAL switch has been
changed
WHITE: n
(where n = A CH, B CH,
PRESET) or ATW: RUN
The OUTPUT/DCC switches
has been set to DCC ON or
OFF
DCC: ON (or OFF)