Cisco Systems CTSATPSX204XK9 Security Camera User Manual


  Open as PDF
of 80
 
D14908.01 SX20 Administrator Guide (TC5.1) | 2012 FEBRUARY | © 2012 Cisco Systems, Inc. All rights reserved. www.cisco.com
35
Cisco TelePresence SX20 Quick Set
ADMINISTRATOR GUIDE
Conference[1..1]EncryptionMode
Set the conference encryption mode. A padlock with the text "Encryption On" or "Encryption
Off" displays on screen for a few seconds when the conference starts.
Requiresuserrole: ADMIN
Valuespace: <BestEffort/On/Off>
BestEffort: The system will use encryption whenever possible.
> In Point to point calls: If the far end system supports encryption (AES-128), the call will be
encrypted. If not, the call will proceed without encryption.
> In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must support
encryption. If not, the conference will be unencrypted.
On: The system will only allow calls that are encrypted.
Off: The system will not use encryption.
Example: Conference 1 Encryption Mode: BestEffort
Conference[1..1]DefaultCallProtocol
Set the Default Call Protocol to be used when placing calls from the system.
Requiresuserrole: ADMIN
Valuespace: <H323/Sip>
H.323: Select H.323 to ensure that calls are set up as H.323 calls.
Sip: Select SIP to ensure that calls are set up as SIP calls.
Example: Conference 1 DefaultCall Protocol: H323
Conference[1..1]DefaultCallRate
Set the Default Call Rate to be used when placing calls from the system.
Requiresuserrole: ADMIN
Valuespace: <64..6000>
Range: Select a value between 64 and 6000 kbps
Example: Conference 1 DefaultCall Rate: 768
Conference[1..1]MaxTransmitCallRate
Specify the maximum transmit call rate to be used when placing or receiving calls.
Requiresuserrole: ADMIN
Valuespace: <64..6000>
Range: Select a value between 64 and 6000 kbps.
Example: Conference 1 MaxTransmitCallRate: 6000
Conference[1..1]MaxReceiveCallRate
Specify the maximum receive call rate to be used when placing or receiving calls.
Requiresuserrole: ADMIN
Valuespace: <64..6000>
Range: Select a value between 64 and 6000 kbps.
Example: Conference 1 MaxReceiveCallRate: 6000
Conference[1..1]VideoBandwidthMode
Set the conference video bandwidth mode.
Requiresuserrole: ADMIN
Valuespace: <Dynamic/Static>
Dynamic: The available transmit bandwidth for the video channels are distributed among the
currently active channels. If there is no presentation, the main video channels will use the
bandwidth of the presentation channel.
Static: The available transmit bandwidth is assigned to each video channel, even if it is not
active.
Example: Conference 1 VideoBandwidth Mode: Dynamic
Conference[1..1]VideoBandwidthMainChannelWeight
The available transmit video bandwidth is distributed on the main channel and presentation
channel according to "MainChannel Weight" and "PresentationChannel Weight". If the main
channel weight is 2 and the presentation channel weight is 1, then the main channel will use
twice as much bandwidth as the presentation channel.
Requiresuserrole: ADMIN
Valuespace: <1..10>
Range: 1 to 10.
Example: Conference 1 VideoBandwidth MainChannel Weight: 5
Conference[1..1]VideoBandwidthPresentationChannelWeight
The available transmit video bandwidth is distributed on the main channel and presentation
channel according to "MainChannel Weight" and "PresentationChannel Weight". If the main
channel weight is 2 and the presentation channel weight is 1, then the main channel will use
twice as much bandwidth as the presentation channel.
Requiresuserrole: ADMIN
Valuespace: <1..10>
Range: 1 to 10.
Example: Conference 1 VideoBandwidth PresentationChannel Weight: 5
Introduction
Table of contents
Web interface
Advanced settings
Appendices
Advanced settings
 previous next