Cisco Systems CTSATPSX204XK9 Security Camera User Manual


  Open as PDF
of 80
 
D14908.01 SX20 Administrator Guide (TC5.1) | 2012 FEBRUARY | © 2012 Cisco Systems, Inc. All rights reserved. www.cisco.com
67
Cisco TelePresence SX20 Quick Set
ADMINISTRATOR GUIDE
ExperimentalConference[1..1]MultistreamStream[1..4]Source
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requiresuserrole: ADMIN
Valuespace: <1/2>
Example: Experimental Conference 1 Multistream Stream 1 Source: 1
ExperimentalConference[1..1]ReceiverBasedDownspeeding
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requiresuserrole: ADMIN
Valuespace: <On/Off>
Example: Experimental Conference 1 ReceiverBasedDownspeeding: Off
ExperimentalCustomSoftbuttonsHoldResume
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
This configuration is used to enable Call Hold and Resume in the OSD. Note that Call Hold and
Resume will be available even if this setting is set to Off, if Multiway is configured.
Requiresuserrole: ADMIN
Valuespace: <Off/On>
Off: Call Hold and Resume is not available (unless Multiway is configured).
On: Call Hold/Resume is available while the system is in a call. It will be available on
softbuttons, and when receiving incoming calls the user will have the option of holding any
current calls while accepting the new call.
Example: Experimental CustomSoftbuttons HoldResume: Off
ExperimentalCustomSoftbuttonsState[1..2]SoftButton[1..5]Type
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requiresuserrole: ADMIN
Valuespace: <NotSet/MainSource/PresentationSource/CameraPreset/Actions/
SpeedDial>
Example: Experimental CustomSoftbuttons State 1 Softbutton 1 Type: NotSet
ExperimentalCustomSoftbuttonsState[1..2]SoftButton[1..5]Value
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requiresuserrole: ADMIN
Valuespace: <S: 0, 255>
Example: Experimental CustomSoftbuttons State 1 Softbutton 1 Value: ""
ExperimentalNetworkServicesUPnPMode
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requiresuserrole: ADMIN
Valuespace: <On/Off>
Example: Experimental NetworkServices UPnP Mode: Off
ExperimentalNetworkServicesUPnPTimeout
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requiresuserrole: ADMIN
Valuespace: <0..3600>
Example: Experimental NetworkServices UPnP Timeout: 0
ExperimentalCTMSSupportMode
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
This configuration tells whether CTMS (Cisco TelePresence Multipoint Switch) is supported or
not.
Requiresuserrole: ADMIN
Valuespace: <Off/On>
Off: CTMS is not supported.
On: CTMS is supported.
Example: Experimental CTMSSupport Mode: On
ExperimentalSystemUnitMenuType
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requiresuserrole: ADMIN
Valuespace: <Indicators/Full>
Example: Experimental SystemUnit MenuType: Full
Introduction
Table of contents
Web interface
Advanced settings
Appendices
Advanced settings
 previous next