Filter
Top Products
65
Adjustments and Settings for Recording
: Setting Time Data
Adjustments and Settings for Recording
1 Position the DISPLAY switch at [UB].
2 Press the HOLD button to display DATE in the display
window.
3 Position the TCG switch at [SET].
4 Use the cursor and SET buttons to set the year, month
and day (Y/M/D).
Note that any later than 2030 cannot be set.
Z button:
Shifts the target (blinking) digit to the right.
Y button:
Shifts the target (blinking) digit to the left.
U button:
Advances the blinking number by one digit.
V button:
Winds back the blinking number by one digit.
5 Press the HOLD button to display TIME in the display
window.
6 Use the cursor buttons to set the hour, minute and
second (h/min/s).
7 Position the TCG switch at [F-RUN] or [R-RUN]. The
internal clock starts at the moment the switch position is
changed.
8 Press the HOLD button to display a time zone (time
difference between local time and Greenwich Mean
Time) in the display window.
9 Position the TCG switch at [SET].
10
Use the U and V buttons to set the desired hours and
minutes ahead of (no sign) or behind (– sign) the
Greenwich Mean Time.
Example: If the local time is 5 hours behind Greenwich
Mean Time, set the time zone to “5:00 –”.
The time zone is always recorded, together with the
date and time, as metadata.
See the table at right to set the time zone according to
your local time.
11
Position the TCG switch at [F-RUN] or [R-RUN] to
accept the time zone.
Notes
When using the unit for the first time, be sure to perform
this setting beforehand. Do not change the setting during
use of the unit.
When the TCG switch is positioned at [SET], thumbnails
cannot be manipulated.
Notes
In step 4, if the TCG switch is positioned at [F-RUN] or [R-
RUN], this also activate the internal clock.
To cancel date, time and time zone settings in process,
hold down the SET button and position the TCG switch at
[F-RUN] or [R-RUN].
Clock accuracy fluctuates between about ±30 seconds per
month when the power is turned off. If more accurate
timekeeping is required, check the time when the power is
turned on and, if necessary, reset the clock.
When the GPS unit AJ-GPS910G is installed, and if it
successfully receives time information, the internal clock
keeps accurate (local) time based on the received time
(Greenwich Mean Time) and the time zone. If the date and
time differ from the actual local time, the time zone may
not be set correctly. Check again, to see if the time zone is
set correctly. (The date and time need not be set again.)
The built-in clock operates for several years on a lithium
battery built into the unit. When the lithium battery is
exhausted, the viewfinder indicates the message
“BACKUP BATT EMPTY” when the power is turned on.
For more information, see [Maintenance] (page 150).
Setting the Internal Clock’s Date and Time
Time
difference
Area
Time
difference
Area
00:00 Greenwich –12:00 Kwajalein
+00:30 –11:30
+01:00 Central Europe –11:00 Midway Island
+01:30 –10:30
+02:00 Eastern Europe –10:00 Hawaii
+02:30 –09:30 Marquesas Islands
+03:00 Moscow –09:00 Alaska
+03:30 Tehran –08:30
+04:00 Abu Dhabi –08:00 Los Angeles
+04:30 Kabul –07:30
+05:00 Islamabad –07:00 Denver
+05:30 Bombay –06:30
+06:00 Dacca –06:00 Chicago
+06:30 Yangon –05:30
+07:00 Bangkok –05:00 New York
+07:30 –04:30
+08:00 Beijing –04:00 Halifax
+08:30 –03:30 Newfoundland Island
+09:00 Tokyo –03:00 Buenos Aires
+09:30 Darwin –02:30
+10:00 Guam –02:00 Mid-Atlantic
+10:30 Lord Howe Island –01:30
+11:00 Solomon Islands –01:00 Azores Islands
+11:30 Norfolk Island –00:30
+12:00 New Zealand
+12:45 Chatham Islands
+13:00
AJ-HPX2700G-VQT1V27_eng.book 65 ページ ２００８年９月２日 火曜日 午後５時４３分