Filter
Top Products
Pan and Tilt Settings (PAN/TILT)
29
D Setting zooming operation options (ZOOM)
When a motion is detected, the camera zooms in and out
automatically.
1 Use the joystick lever (xy) to select [ZOOM] and use the
lever (vw) to select zooming mode.
Available settings:
•OFF: Disables the auto zooming. (Initial setting)
•IN: Performs detection at the center of the screen
and zooms in along the optical axis.
•OUT: Performs detection over the full screen (except
for the masked area) and zooms out along the
optical axis.
• IN-MOV: Performs detection over the full screen (except
for the masked area) and zooms in at the position
where motion was detected.
2 Select the optical zoom magnification power (RATIO)
according to the zooming mode you selected.
Available settings:
•IN: x1.4, x2, x2.8, x4, x5.6, x8, FULL (zooming in to
the TELE end), MANU (manual setting)
•OUT: x1/1.4, x1/2, x1/2.8, x1/4, x1/5.6, x1/8, FULL
(zooming out to the WIDE end), MANU (manual
setting)
• IN-MOV: x1.4, x2, x2.8, x4, x5.6, x8, FULL (zooming in to
the TELE end), MANU (manual setting)
Memo: When selecting “MANU”, the RATIO SETTING screen
appears. While monitoring the actual image and performing
zooming operation, specify the zoom magnification power,
then press the [ENTER] button. The zoom magnification
power value appears in the bottom left of the screen.
3 Select the duration for the zooming operation (TIME)
Available settings: (common to all zooming modes)
5S, 10S, 15S, 20S, 30S, 45S, 1M, 2M, 3M, 4M, 5M
(S: Second, M: Minute)
E Setting the interval after which the next alarm
becomes in effect (DURATION)
When a motion is detected and an alarm signal is output, another
alarm signal will not be output until the duration specified in this
setting has passed.
Use the joystick lever (xy) to select [DURATION] and use the
lever (vw) to select the interval after which the next alarm
becomes in effect.
Available settings: 5S, 10S, 15S, 20S, 30S, 45S, 1M, 2M, 3M,
4M, 5M (S: Second, M: Minute)
The following settings are common to the ones performed in the
camera and lens settings. See their respective reference pages.
• IRIS (Page 11)
• WHITE BALANCE (Page 12)
• BLC (Page 14)
• SHUTTER (Page 16)
• APERTURE (Page 17)
• AGC (Page 17)
• GAMMA (Page 18)
• DAY/NIGHT (Page 19)
Memo: • The IRIS, SHUTTER and MOTION functions can be used
in the combination shown in the table below.
F: Function is set T: Not allowable E: Allowable
• : When exiting individual menu, settings will be
cancelled.
☞ After completing setting, use the lever to move the cursor to
[MENU] and select “BACK” or “END”.
b Grouping the preset positions
(SEQUENCE GROUP)
Each preset position can be assigned to a group (A to D). The group
can be used for the Sequence mode to monitor multiple surveillance
locations sequentially.
1
Use the joystick lever (xy) to select [PRESET
POSITION] – “SET y”, and press the [ENTER]
button.
The preset map screen appears.
The value you can select here should be within the
duration specified in the [DURATION] setting (see step E
below).
B
Setting related options other than motion
sensor
IRIS AUTO: SENSE UP (ON) FTT T T
MANU: EI (ON) TFT
TE
SHUTTER LONG TTFTT
SHORT TTTFE
MOTION TETEF
No. 27
No. 15
No. 4
No. 1
No. 8
No. 30
No. 22
No. 11
No. 2
No. 20
PRESET NO.SELECT
1:A 11:B 21:- 31:-
2:B 12:- 22:B 32:-
3:- 13:- 23:- 33:-
4:A 14:- 24:- 34:-
5:- 15:A 25:- 35:-
6:- 16:- 26:- 36:-
7:- 17:- 27:A 37:-
8:A 18:- 28:- 38:-
9:- 19:- 29:- 39:-
10:- 20:B 30:B 40:-
MENU
BACK
Group A Group B