Filter
Top Products
SYSTEM CONFIGURATIONS
LEVEL 1 - 960 X 16, Four Bay System
A four bay, Level 1 system allows a maximum of 960 video
inputs switched to a maximum 16 video outputs. Bays one,
two, and three each consist of 256 video inputs. Bay four
consists of 192 video inputs and 16 video outputs.
From the rear of bay one, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-11 with 16 BNCs for
connection to the 2024VOM-1 modules in bay four, followed
by sixteen 2016AVIM-1 modules, inputs 1 - 256.
From the rear of bay two, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-21 with 16 BNCs for
connection to the 2024VOM-1 modules in bay four, followed
by sixteen 2016AVIM-1 modules, inputs 257 - 512.
From the rear of bay three, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-31,with 16 BNCs for
connection to the 2024VOM-1 modules in bay four, followed
by sixteen 2016AVIM-1 modules, inputs 513 - 768.
From the rear of bay four, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-00, followed by
twelve 2016AVIM-1 modules for inputs 769 - 960, and four
2024VOM-1 modules for outputs 1 - 16.
Smaller matrices, such as those ordered with future expansion
in mind, may have fewer modules installed.
IDENTIFY THESE MODULES CAREFULLY
BEFORE PROCEEDING.
Data Interconnect: See Level 1 - 448 X 16, Two Bay System
and connect all bays in a similar manner.
Video Interconnections: The 16 video outputs from bays 1,
2, and 3, located on the rear panel of the 2010DB-11 ,
2010DB-21 , and 2010DB-31 , are grouped by
fours and identified by the icons.
Each 2024VOM-1 is similarly grouped with three sections of
four BNCs, with identifying icons. A fourth section of four
BNCs is used for video output connections. See Figure 21,
Video Output Module, page 9.
Using high grade RG-59U video cables, connect the topmost
BNC from bay 1 on the 2010DB-11 panel, numbered 1, to the
topmost input BNC, labeled 1 on the 2024VOM-1 of bay 4, for
output 1, matching icon to icon.
Continue in this manner until 1-4 of the 2010DB-11 panel are
connected to inputs 1-4 of the first 2024VOM-1. Proceed to
the next group of four BNCs on the 2010DB-11 of the first
bay. Connect these four to the second 2024VOM-1 for outputs
5 - 8. Continue in this manner until all 16 connections of the
2010DB-11 panel are connected to all of the 2024VOM-1
modules.
Connect bay 2 in a similar manner to the 2024VOM-1 modules
of bay 4 for video outputs 1-16, matching icon to icon.
Connect bay 3 in a similar manner to the 2024VOM-1 modules
of bay 4 for video outputs 1-16, matching icon to icon.
See Appendix Figure A18, Video Interconnections, for
illustration of these connections.
If there are less than four 2024VOM-1s in the system, the
remaining BNCs on the 2010DB-XX do not require any
connection.
Video Input Connections: See Level 1 - 448 X 16, Two Bay
System and connect in a similar manner.
Video Output Connections: See Level 1 - 448 X 16, Two
Bay System and connect in a similar manner.
In the Appendix, see Figure A5, Level 1 - 960 X 16, Four Bay
System.
24