Filter
Top Products
GENERAL DESCRIPTION
The MegaPower II AD1024 Switcher/Control System is an
integrated matrix switching and control system for CCTV
surveillance systems. It is capable of controlling up to 1024
video input sources such as cameras, and 128 video outputs
such as monitors and video tape recorders.
The AD1024 system consists of a matrix switching bay, its
power supply module, a data receiver/buffer module, the
required video input modules (VIM), video output modules
(VOM), and appropriate rear panels. All AD1024 systems are
controlled with a separate central processing unit (CPU) and
keyboard.
AD1024 Switcher/Control Systems are supplied as completely
configured switching bays. Only the bay interconnections, the
CPU connections, the video input and output connections, and
any optional accessory connections need be made prior to
operation. The AD1024 system, as delivered, is a complete
system with all inputs terminated in 75 ohms. Each bay is
packed in a separate shipping carton labeled with the AD1024
bay assembly number on the outside of the carton.
Matrix Switching Bay
The 2010R and 2020R switching bays include the physical
chassis, a back plane, a power supply module, and a data
receiver. Each bay has the capability of looping the DATA
LINE input and looping an external vertical synchronization
pulse to other bays. Each bay also accommodates a
combination of video input modules and video output modules,
up to a total of 16 modules.
Power: 50 watts (full system)
Size: 10-1/2” height. Full-width 19” rack mount
Weight: 60 lbs. (28 kg) (full system)
CPU (Central Processing Unit)
The CPU for the AD1024 system is a separate rack-mounted
unit that includes its own power supply, system software, ten
RS-232 ports, a system diagnostic monitor output, and two
DATA LINE outputs. These DATA LINE outputs distribute
high speed data control signals to the AD1024 matrix
switching bays and optional accessories.
AD1024 Central Processing Unit
Power: 4 watts
Size: 1.75” height. Full-width 19” rack mount
Weight: 10 lbs. (4.5 kg)
OPTIONAL EQUIPMENT
The following separate units may be connected to the AD1024
system for added capabilities. For specific information, refer
to the respective data sheets.
2091 Control Code Generator/Distributor
The 2091 provides 64 control-code outputs for control of 1640
and 1680 Series Receivers actuating pan/tilt; lens zoom, focus,
and iris; and auxiliaries at suitably-equipped camera sites.
2031 Switcher/Follower,
2032 Alarm Responder,
2033 Auxiliary Follower
The 2030 Series Followers switch external circuits when
designated cameras are called to designated monitors (2031),
when designated monitors are in alarm conditions (2032), or
when designated auxiliaries are called up or designated
cameras are alarmed (2033).
ADULP Looping Panel
The ADULP Looping Panel is used to facilitate the looping of
video signals for the AD1024 system from external inputs or to
external devices such as time-lapse video recorders, switchers,
monitors, etc.
Other Switcher/Control System Accessories
• 1640 and 1680 Series Receivers
• 1670 and 2078 Series Keyboards
• 1680MG Manchester Generator
• 1683 Control Code/PSK Modem
• 1981 Port Expander
• 2081 Port Expander
• 1983 Code Converter
• 2083 Code Translators
• 2096 Alarm Interface Unit
• 1985A Hot Switch
This installation should be made by qualified service personnel
and should conform to all local codes. Safeguards must be
taken to avoid unintentional operation by employees and
maintenance personnel working about the premises, by falling
objects, by customers, by building vibration, and by similar
causes.
1
GENERAL DESCRIPTION
IF YOU ENCOUNTER ANY PROBLEMS
OPERATING THIS UNIT, OR NEED ASSISTANCE,
CALL OUR TECHNICAL SUPPORT CENTER AT:
within the United States: 1-800-442-2225
outside the United States: (845) 624-7600