Filter
Top Products
SYSTEM CONFIGURATIONS
LEVEL 3 - 768 X 48, Ten Bay System
A seven bay, Level 3 system allows a maximum of 768 video
inputs switched to a maximum 48 video outputs. Bays one
through nine consists of 256 video inputs, and bay ten consists
of 48 video outputs.
From the rear of bay one, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-11 with 16 BNCs for
connection to the 2024VOM-1 modules in bay ten, followed
by sixteen 2016AVIM-2 modules, inputs 1-256.
From the rear of bay two, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-21 with 16 BNCs for
connection to the 2024VOM-1 modules in bay ten, followed
by sixteen 2016AVIM-2 modules, inputs 257-512.
From the rear of bay three, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-31 with 16 BNCs for
connection to the 2024VOM-1 modules in bay ten, followed
by sixteen 2016AVIM-2 modules, inputs 513-768.
From the rear of bay four, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-12 with 16 BNCs for
connection to the 2024VOM-1 modules in bay ten, followed
by sixteen 2016AVIM-3 modules, inputs 1-256.
From the rear of bay five, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-22 with 16 BNCs for
connection to the 2024VOM-1 modules in bay ten, followed
by sixteen 2016AVIM-3 modules, inputs 257-512.
From the rear of bay six, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-32 with 16 BNCs for
connection to the 2024VOM-1 modules in bay ten, followed
by sixteen 2016AVIM-3 modules, inputs 513-768.
From the rear of bay seven, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-13 with 16 BNCs for
connection to the 2024VOM-1 modules in bay ten, followed
by sixteen 2016AVIM-4 modules, inputs 1-256.
From the rear of bay eight, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-23 with 16 BNCs for
connection to the 2024VOM-1 modules in bay ten, followed
by sixteen 2016AVIM-4 modules, inputs 257-512.
From the rear of bay nine, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-33 with 16 BNCs for
connection to the 2024VOM-1 modules in bay ten, followed
by sixteen 2016AVIM-4 modules, inputs 513-768.
From the rear of bay ten, the modules are installed at the
factory in the following manner; the far right module is the
2010PS, the next module is the 2010DB-00, followed by
twelve 2024VOM-1 modules, installed left to right, for outputs
1-48.
Smaller matrices such as those ordered with future expansion
in mind, may have fewer modules installed.
IDENTIFY THESE MODULES CAREFULLY
BEFORE PROCEEDING.
Data Interconnect: See LEVEL 3 - 192 X 48, Three Bay
System and connect all bays in a similar manner.
Video Interconnections: The 16 video outputs from bay 1,
through 9 located on the rear panel of the 2010DB-11, -12, -13,
, -21, -22, -23, , and on rear panels -31,-32, and
-33 respectively.
They are grouped by fours and identified by their icons.
Each 2024VOM-1 is similarly grouped with three sections of
four BNCs, with identifying icons. A fourth section of four
BNCs is used for video output connections. The left-most
2024VOM-1 module is assigned to outputs 1 - 4, the next for
outputs 5 - 8, etc. See Figure 21, page 9.
Using high grade RG-59U video cables, connect the topmost
BNC from bay 1 on the 2010DB-11 panel, numbered 1, to the
2024VOM-1 in bay 10, for output 1, matching icon to icon.
Continue in this manner until connections 1-4 of the 2010DB-
11 panel are connected to inputs 1-4 of the first 2024VOM-1.
Proceed to the next group of four BNCs on the 2010DB-11 of
the first bay and connect these four to the second 2024VOM-1
of bay 10 for outputs 5-8. Continue in this manner until all 16
connections of the 2010DB-11 panel are connected to the
2024VOM-1s for outputs 1-16.
Connect bay 4 in a similar manner to the 2024VOM-1s of bay
10 for video outputs 17-32, matching icon to icon.
Connect bay 7 in a similar manner to the 2024VOM-1s of bay
10 for video outputs 33-48, matching icon to icon.
Connect the top-most BNC from bay 2 on the 2010DB-21
panel, numbered 1, to the 2024VOM-1 in bay 10, for output 1,
matching icon to icon.
42