Filter
Top Products
40
Setup (Initial settings)
The memory card recorder’s main settings are performed while making selections using a system of menus.
If a TV monitor has been connected to the VIDEO OUT 3 connector or SDI OUT 3 connector (optional) on the rear
panel and the SUPER switch is set to [ON], the setting menus are displayed on the TV monitor.
HEADPHONES
PULL PULL
AUDIO MIX
1&2
CH1/3 CH2/4
REC CH1/3
REC CH2/4
3&4
CH1/3 CH2/4
AUDIO MON SEL
AUDIO VOL SEL
LRMIX
REC
PB
UNITY
VAR
METER
FULL/FINE
INPUT SELECT
VIDEO AUDIO
CH 1 CH 2 CH 3 CH 4
COUNTER
MENU
TC PRESET
SELECT
SLOT
RESET
THUMBNAIL
MARKER
BAR
MENU
SET
SEARCH
RECPLAY
FFREW STOP
PREV NEXT
SHIFT
SHTL
PUSH
JOG
SLOW
Memory Card Recorder AJ-
ENC
CONTROL
REMOTE
LOCAL
VIDEO
LEVEL
PRESET
MANUAL
CHROMA
LEVEL
PRESET
MANUAL
SET UP
PRESET
BLK
MANUAL
HUE
PRESET
CHROMA PH
MANUAL
TC
REGEN
PRESET
REC RUN
FREE RUN
DIAG
ON
POWER
USB 2.0
OFF
REMOTE
LAN
USB
1
2
3
4
5
SUPER
ON
OFF
TCG
INT
EXT
MODE
PB
EE
REC INH
ON
OFF
DVCPRO 50
DVCPRO
DV
PLAY LIST EVENT
INSERT
DELETE
GO TO
ENTRY OUTIN
(1)
(6) (4) (2)
(3)
Changing the settings
(1) Press the MENU button
The setup menu screen appears on the TV monitor, and
the setup menu item number appears on the counter
display.
Each time the FF button is pressed (for about 1.5
seconds), the item number and item name are displayed
alternately.
(If a setup was performed previously, the screen on
which the last change was made is displayed.)
(2) Turn the search dial to select the item to be set
The menu screen cursor ( ) moves, and the item
number on the display flashes.
•When the dial is turned clockwise, the item number is
incremented from 001 → 002 → 003 → 004 and so on;
conversely, when it is turned counterclockwise, the
item number is decremented.
•When the FF button or REW button is pressed while
holding down the PLAY button, the next or previous
item is selected.
•Whenever possible, limit the use of the search dial to
the JOG mode.
(3) At the position where the change is to be
made, turn the search dial while holding down
the SEARCH button
The settings on the menu screen and display now flash.
When the dial is turned clockwise, the setting number is
incremented; conversely, when it is turned
counterclockwise, it is decremented.
(4) Upon completion of the setting, release the
SEARCH button
•When the search dial is in the SHTL mode, the item will
move unless the dial is set to the center position.
(5) When other items are to be changed, repeat
steps (2) to (4)
(6) Press the SET button
The changes are stored in the memory.
To disregard the new settings and restore the old settings
instead, press the MENU button.
•To return the setup contents to the factory settings
(initial settings), press the RESET button while the menu
is displayed. The following message is displayed.
If the PLAY button is now pressed, the factory settings
are reinstated.
SETUP - MENU INIT SET
YES<PLAY> / NO<STOP>
Notes:
•If the RESET button is pressed to restore the factory
settings, only the user files currently in use are
restored. The other user files remain unaffected.
•The changes made to the SYSTEM menu contents
are recorded even by pressing the MENU button to
close the menu screen.
SUPER switch (set to [ON])