Panasonic PV-GS32 Camcorder User Manual


 
57
Others
LCD Monitor/Viewfinder/Lens Hood
LCD Monitor
• In a place with drastic temperature changes,
condensation may form on the LCD Monitor. Wipe it
with a soft dry cloth.
• If your Camcorder is extremely cold when you turn
its power on, the image on the LCD Monitor is
slightly darker than usual at first. However, as the
internal temperature increases, it goes back to the
normal brightness.
Viewfinder
• Do not direct the Viewfinder or Lens to the sun.
Internal components may be seriously damaged.
When the Camcorder is used with a large capacity
Battery attached to it, it is not practical to look in the
Viewfinder from behind the Battery.
Lens Hood
• When you wish to attach the Tele Conversion Lens
(not supplied), Wide Conversion Lens (not supplied),
MC Protector (not supplied), or ND Filter (not
supplied), rotate these in a clockwise direction.
• If you push the [W/T] Lever toward [W] during
recording with the filter and conversion lens attached
to the Camcorder, 4 corners of the image may
become dark (vignetting). For details, please refer to
the operating instructions of your accessories.
Extremely high precision technology is employed to
produce the LCD Monitor screen featuring a total
of approximately 105,000 pixels. The result is more
than 99.99 % effective pixels with a mere 0.01 %
of the pixels inactive or always lit. However, this is
not a malfunction and does not affect the recorded
picture.
Extremely high precision technology is employed
to produce the Viewfinder screen featuring a total
of approximately 113,000 pixels. The result is more
than 99.99 % effective pixels with a mere 0.01 %
of the pixels inactive or always lit. However, this is
not a malfunction and does not affect the recorded
picture.
Before Requesting Service
(Problems and Solutions)
Power/Body
The Camcorder power cannot be turned on.
• Is the battery fully charged? Use a fully charged
battery.
• The battery protection circuit may have operated.
Attach the battery to the AC adaptor for 5 to
10 seconds. If the Camcorder still cannot be used,
the battery is faulty.
The Camcorder power is turned off
automatically.
• If you set [ POWER SAVE] to [5 MINUTES]
and do not operate the Camcorder for about
5 continuous minutes, the power is automatically
turned off for tape protection and power
conservation. To resume recording, turn the [OFF/
ON] switch to [OFF]. Then turn it to [ON] again.
(p. 49)
The Camcorder power does not stay on long
enough.
• Is the battery low? If the remaining battery power
indication is flashing or the message [LOW
BATTERY] is displayed, the battery has run down.
Charge the battery or attach a fully charged battery.
(pp. 11~12)
• Has condensation occurred? When you carry the
Camcorder from a cold place into a warm place,
condensation may occur inside it. If so, the power
is turned off automatically, disabling all operations
except for taking cassettes out. Wait until the
condensation indication disappears. (p. 55)
Battery runs down quickly.
• Is the battery fully charged? Charge it with the AC
adaptor. (p. 11)
• Are you using the battery in an extremely cold
place? The battery is affected by ambient
temperature. In cold places, the operating time of
the battery becomes shorter.
• Has the battery worn out? The battery has a limited
life. If the operating time is still too short even
after the battery is fully charged, depending on the
usage, the battery has worn out and can no longer
be used.
The Camcorder cannot be operated though
powered up.
The Camcorder does not operate normally.
• Remove the cassette and then press the [RESET]
button. (p. 60) If normal conditions are not restored
yet, turn off the power. Then, about 1 minute
later, turn on the power again. (Conducting the
above operation when the Access Lamp is on may
destroy the data on the card.)