Filter
Top Products
132
Others
Make sure that peripheral devices are used in accordance with their
operating environment.
Compatible Network Cameras
Memo :
●
When sending out audio data to VN-V26U, make sure that the
firmware version of VN-V26U is 1.01 or a newer version. (VR-
N1600U/E)
Connecting a UPS
Connecting an uninterruptible power supply (UPS) to the hard disk
will protect it from damage by automatically shutting down all
operations prior to switching off the power supply in the event of a
power failure.
1 Press and hold the [FUNCTION] button, and
press the [3/ ] keypad button at the same time
to start up the [UPS SetUp] screen
2 Select AUPS ModeB and press the [OK] button
3 Connect the UPS communication cable to the
[SERIAL] port on the rear panel
4 Connect the power cable of this unit to the UPS
power output connector
5 Switch on the power of the UPS, followed by the
power of this unit
Note :
●
Consult your nearest JVC dealer or service center for details on
the types of UPS that can be used.
●
Make sure that the UPS communication cable is connected
before switching on the power of this unit.
●
Do not disconnect the communication cable when operations
are in progress.
●
When a power failure occurs while formatting a hard disk or
archiving, subsequent operations may be affected even when a
UPS is connected.
●
The recorded images may not be played back properly if they
are not archived before the power failure. (
A
Page 110)
●
If you are not using a UPS, do not select [UPS SetUp] on the the
[UPS SetUp] screen. Inappropriate selections may affect
subsequent operations.
External Hard Disk Drives
You can connect an external hard disk drive to the serial terminal at
the rear of this unit. External hard disk drives can be combined with
this unit in the following ways. Combinations other than those below
are not possible.
●
500 GB (1 unit)
●
1 TB (1 unit)
●
1 TB (1 unit) + 2 TB (1 unit)
●
2 TB (1 unit)
●
2 TB (up to 2 units)
Connecting the External Hard Disk Drive
1 Press and hold the [OPERATE] button for
about2 seconds to turn off the power
2 Turn off the power switch on the rear panel
Note :
●
Make sure that you turn off the power switch.
3 Connect the external hard disk drive to the
[SERIAL] port on the rear panel, and switch on
the power
●
Make sure that you switch on the power to the external
hard disk drive before switching on this unit. The system
may not recognize the external drive if it is not switched on
beforehand.
4 Switch on the power of this unit
●
If recording is in progress, a [New HDD was found. Are
you OK to stop recording and format new HDD?]
confirmation message appears.
Compatible Equipment
Function
JPG PTZ
Audio
PTZ
Joystick
MPG4
VMD
Event
JVC
VN-V25U
RR
JVC
VN-V26U
RRR
JVC
VNV686U
RR RR
JVC
VN-C20
RR
JVC
VN-C655
RR R
JVC
VN-C625
RR R
JVC
VN-E4
RRRR
JVC
VN-C215
RR
AXIS 206
RR
AXIS 207
RR RR
AXIS 211
RRR RR
AXIS 212
RRRRRR
AXIS 213
RRRRRR
AXIS 214
RRRRRR
AXIS 216
RRR RR
AXIS 225
RR RR
Verint S1700
RRR
Verint S1704
RRR
Verint S1708
RRR
Verint S1900
R
Verint S2700E
R