Filter
Top Products
● Password Lock (PASSWORD LOCK)
Caution:
For security, do not operate your VCR for recording
while the password menus are displayed on the
monitor.
A 3-digit number is used for a password to limit
access to all settings.
1. Move the cursor to PASSWORD LOCK, then select
ON or OFF with the joystick.
Note:
ON or OFF can be selected only after going
through the password verification.
OFF: You can change all settings.
ON: You cannot change settings at all nor operate
AUTO PAN, SEQ, SORT, and PATROL.
2. Press the CAM (SET) button.
Password Verification
3. The password verification menu appears.
3-1 Select a numeral for the first digit with the joy-
stick, and press the CAM (SET) button. Though
the entered password is not displayed, the up-
arrow moves one character to the right.
3-2 Repeat the above step for the 2nd and 3rd dig-
its.
Default: 123
3-3 The cursor moves to OK after all the three digits
have been entered. Unless you want to change
the password, press the CAM (SET) button.
If the correct password is entered, the screen
returns to SET UP MENU. ON and OFF settings
are the same as made on the SET UP MENU
menu is as set in step 1.
If a wrong password is entered, the screen
returns to the verification menu. Repeat steps 3-1
to 3-3 to verify the password.
** SET UP MENU **
PRESET 1
MAP
HOME POSITION
SELF RETURN
AUTO MODE
AUTO PAN KEY
DIGITAL FLIP
SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK ON
OFF
OFF
OFF
AUTO PAN
ON
** PASSWORD? **
0 1 2 3 4 5 6 7 8 9
. . .
↑
OK RESET
NEW PASSWORD
RET
-34-
AUTO PAN: Assigns the auto panning function to
the button.
SEQ: Assigns the SEQUENCE function to the but-
ton.
SORT: Assigns the SORT function to the button.
PATROL: Assigns the PATROL PLAY function to the
button.
Note:
AUTO PAN LED on the controller does not light if
something other than AUTO PAN is assigned.
AUTO PAN does not stop with the AUTO PAN
button.
If PASSWORD LOCK is set to ON, you cannot
operate AUTO PAN, SEQ, SORT, and PATROL
even by pressing the AUTO button.
■ Digital Flip Setting (DIGITAL FLIP)
Move the cursor to DIGITAL FLIP and select ON or OFF
with the joystick.
OFF: The tilt range is limited from 0° to 90°.
ON: The digital flip function allows the tilt angle to
widen up to 180°. The image on the monitor
screen is flipped horizontally and vertically at the
tilt angle of approx. 135° (If the camera is
installed on a ceiling).
Note:
The tilt range narrows from 0° to 90° if PAN
LIMIT is set to ON.
Notes:
• Digital flip functions while moving the joystick down-
wards. In case of moving the joystick to other direc-
tions, it does not function.
• When OFF is selected for DIGITAL FLIP, the follow-
ing operations are required to move the camera
180° vertically.
1) Move the joystick downwards to aim the camera
down.
2) Move the joystick to the right or left to rotate the
camera 180° horizontally.
3) Move the joystick upwards.
• To set the preset position directly from WV-CU360
System Controller, it is temporarily required to set
both the electronic zoom function and digital flip
function to OFF.
Tilt range setting is disabled between 90° and 185°.
** SET UP MENU **
PRESET 1
MAP
HOME POSITION
SELF RETURN
AUTO MODE
AUTO PAN KEY
DIGITAL FLIP
SPECIAL1
CAMERA
RS485 SET UP
PASSWORD LOCK OFF
OFF
OFF
OFF
AUTO PAN
ON